On-disc timer programming, Pg. 40 – JVC SR-MV50U User Manual
Page 40
Filename [SR-MV50U_07DVD Operation2.fm]
Masterpage:Left+
40
EN
Page 40
February 24, 2006 9:43 am
OPERATIONS ON DVD DECK
On-Disc Timer Programming is a function used with discs that are
especially intended for a specific program. The disc is then
programmed for a program you always watch every day or every
week. Since older programs are automatically overwritten, a single
DVD-RAM/RW (VR mode) disc can be used without worrying
about how much recording capacity remains. (
You can program each disc to timer record as many as 8 programs.
To Make The Disc For On-Disc Timer Programming
1
Load a recordable disc.
2
Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
3
Press PROG/CHECK to access the Program Check screen.
4
When On-Disc Timer Programming is made for the first
time on the disc
Press rt to select “DISC TIMER PRGM”, then press ENTER.
● When some programs are recorded on the disc, a caution message
appears. In such a case, backup the programs as required, then
format the disc before making On-Disc Timer Programming.
(
When On-Disc Timer Programming has already been made on
the disc
Press rt to select “NEW TIMER PROGRAM”, then press
ENTER.
5
Press rt to set the desired date.
● The current date appears on the TV screen. The date you enter
appears in its place.
6
Press w e to select “START”, then press rt to set the desired
start time.
● Each press of rt increases/decreases the start time in 1-minute
interval.
● To increase/decrease the start time in 30-minutes interval, press and
hold rt.
7
Press w e to select “STOP”, then press rt to set the desired
stop time.
● Each press of rt increases/decreases the stop time in 1-minute
interval.
● To increase/decrease the stop time in 30-minutes interval, press and
hold rt.
8
Press w e to select “CH”, then press rt to select the desired
channel.
9
Set “DAILY/WEEKLY” option.
● Refer to step 6 in “VCR Plus+ Timer Programming” (
● It is necessary to set “DAILY/WEEKLY” option for On-Disc Timer
Programming. (
੬ pg. 38, “Daily/Weekly Recording”)
10
Set the other recording options as required.
● You can select XP, SP, LP, EP or FR480 mode for “REC MODE”.
However, you cannot select FR (JUST), FR60–FR360 and FR420.
● Refer to step 6 in “VCR Plus+ Timer Programming” (
● It is not possible to use the Free Rate function. (
11
Press ENTER to access the Program Confirmation screen.
12
Press ENTER to complete timer programming.
● To program another timer, repeat steps 3 – 12.
To Timer record The Program With The Programmed
Disc
1
Load a programmed disc.
2
Press DVD TIMER (#). The unit turns off and “
” appears
on the front display panel. The DVD timer indicator also lights up
on the front display panel and the VCR deck is automatically
selected. When the VCR deck is in timer standby mode, the unit is
automatically turned off.
● To disengage the timer mode, press 1 again.
NOTES:
● When On-Disc Timer Programming overlaps with other timer
programming, for example VCR Plus+ Timer Programming, no
caution message will be displayed.
However, when On-Disc timer programs overlap, a caution message
will be displayed.
● On-Disc Timer Programming is not possible on a DVD-RW disc
formatted in video mode. (
● The information of a program recorded with On-Disc Timer
Programming is not stored in the library. (
● The play list is not created for the programs recorded with On-Disc
Timer Programming. (
● VCR Plus+ Timer Programming is not possible on the discs used
exclusively for On-Disc Timer Programming.
● Manual Timer Programming is not possible on the On-Disc Timer
Programmed disc. (
● Basic Recording is not possible on the On-Disc Timer Programmed
disc. (
● The On-Disc Timer Programming function does not work on the unit
form other manufactures even if the On-Disc Timer Programmed disc
is loaded.
● The beginning of a program may not be recorded. Also, if the 1st
program’s recording stop time and the 2nd program’s recording start
time is the same, the ending of the 1st program may not be recorded.
● If there is a power cut while recording, the recordings before the
power cut are not guaranteed.
On-Disc Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
ATTENTION:
● On-Disc Timer Programming is possible only with the disc for On-
Disc Timer Programming.
● If data is recorded on a disc for On-Disc Timer Programming using
a unit from another manufacturer, On-Disc Timer Programming
may no longer function properly.
1
4
7
2
5
8
0
3
6
9
PROG/CHECK
ENTER
DVD TIMER (#)
rtw e
VCR/DVD
1
SR-MV50US.book Page 40 Friday, February 24, 2006 9:43 AM