JVC SR-MV50U - Manual (Page 72)

Filename [SR-MV50U_11Subsidiary.fm]
Masterpage:Left+
72
EN
Page 72 February 24, 2006 9:43 am
SUBSIDIARY SETTINGS
8 PICTURE CONTROL — AUTO / EDIT / SOFT / SHARP
This feature helps you to adjust the playback picture quality
according to your preference. Normally select “AUTO”.
AUTO : Picture quality is adjusted automatically.
EDIT : Minimizes picture degradation during editing (recording and
playback).
SOFT : Reduces image coarseness when viewing overplayed tapes
containing a lot of noise.
SHARP : Clearer, sharper-edged picture when viewing images with
lots of flat, same-colored surfaces such as cartoons.
NOTES:
● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will
not change until you select another mode.
● When you select “EDIT” to dub tapes, be sure to select “NORM” after
you finish dubbing the tapes.
● When “VIDEO CALIBRATION” is “OFF”, “PICTURE CONTROL”
switches automatically from “AUTO” to “NORM”.
8 VIDEO STABILIZER — ON / OFF
When this function is set to “ON”, you can automatically correct
vertical vibration in the picture when playing back unstable
recordings made on another recorder.
NOTES:
● When you finish viewing a tape, be sure to set this function to “OFF”.
● Regardless of the setting, this function has no effect during recording
and during special effects playback.
● The on-screen display may jitter vertically when this function is set to
“ON”.
● To watch recordings with close-caption, set this function to “OFF”.
8 AUTO SP]EP TIMER — ON / OFF
When this function is set to “ON”, the unit automatically switches to
EP mode to allow complete recording if there is not enough tape to
record the entire program while timer recording in SP mode.
For Example:
Recording a program of 140 minutes in length onto a 120-minute
tape
Make sure you set this function to “ON”, before the timer recording
starts.
NOTES:
● If you have programmed the unit to timer record 2 or more programs,
the second program and those thereafter may not fit on the tape if
you set “AUTO SP]EP TIMER” to “ON”. In this case, make sure the
mode is not engaged, then set the tape speed manually during timer
programming.
● In order to ensure that the recording fits on the tape, this feature may
leave a slight non-recorded section at the end of the tape.
● There may be some noise and sound disturbance at the point on the
tape where the unit switches from SP to EP mode.
● The Auto SP
] EP Timer feature will not work properly on the
following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
8 SUPERIMPOSE — AUTO / ON / OFF
When this function is set to “AUTO”, various operational indicators
appear on the TV screen.
AUTO : To superimpose operational indications for approximately
five seconds just after the corresponding operation.
ON : Functions in the same way as “AUTO”. However, when “ON” is
selected, the counter display ( ੬ pg. 15) will always be displayed
during playback.
OFF : To turn off superimposed indications.
NOTES:
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting.
● During playback, the operation mode indicators may be disturbed
depending on the type of tape being used.
8 DIGITAL R3 — ON / OFF
When this function is set to “ON”, the Digital 3R picture system
applies edge correction to the luminance signal to enhance detail.
NOTES:
● Normally it is recommended to keep “DIGITAL 3R” set to “ON”.
● Depending on the type of tape being used, picture quality may be
better with “DIGITAL 3R” set to “OFF”.
● If you use the unit as the source player for editing, be sure to set
“DIGITAL 3R” to“OFF” before starting.
8 BLUE BACK — ON / OFF
When this function is set to “ON”, the TV screen becomes all blue
when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals, set
this function to “OFF”.
8
2ND AUDIO RECORD — ON / OFF
When this function is set to “ON”;
If a SAP program is received, the SAP audio is recorded on L/R
tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on L/
R tracks.
When this function is set to “OFF”, the SAP audio cannot be
recorded.
NOTE:
When the channel is changed on the unit;
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
Total 140 minutes
Approximately 110 minutes Approximately 30 minutes
SP mode EP mode
SR-MV50US.book Page 72 Friday, February 24, 2006 9:43 AM