JVC DR-MV5BEK - Manual (Page 57)

Masterpage:Right+
EN
57
Filename [MV5SEK_09Advanced Operation.fm]
ADVANCED PLAYBACK
Page 57Wednesday, 31 August 2005 19:58
4
Press the number buttons to enter the desired item number,
then press ENTER.
● Playback starts from the selected section.
Examples:
A To select track 5, press the number button “5”.
B To select track 15, press the number button “1” and “5”.
C To select track 25, press the number button “2”, then “5”.
If you have specified a wrong selection
Press CLEAR (8) on the remote control unit and repeat the above
procedures from step 2.
To clear the on-screen bar
Press ON SCREEN.
NOTES:
● When “X” is displayed on the TV screen in step 4, the chapter you
have selected is not contained in the disc, or chapter search does not
work on the disc.
● Before you press ENTER, playback may start automatically when
you enter the section’s number depending on the disc.
● This function is not possible for a Video CD with PBC function.
Time Search
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a programme (DVD-
RAM, DVD-R, DVD-RW and DVD VIDEO) or a disc (Video CD and
Audio CD).
1
Press ON SCREEN twice to access the on-screen bar.
2
Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
3
Press the number buttons to enter the time, then press
ENTER. Playback starts from the specified time.
Example:
To play back from a point 12 (minutes): 50 (seconds) elapsed.
If you have specified a wrong selection,
Press CLEAR (8) on the remote control unit and repeat the above
procedures from step 2.
To clear the on-screen bar
Press ON SCREEN.
NOTES:
● When “X” is displayed on the TV screen in step 3, you have selected
a point that exceeds the recording time of the disc.
● Some DVD VIDEO discs do not contain time information, and it is not
possible to use the Time Search function. In such cases, “X” is
displayed on the TV screen as well.
● This function is not possible for a Video CD with PBC function.
Adjusting The Picture Quality
You can obtain optimal picture quality by selecting an appropriate
picture mode.
1
Press ON SCREEN twice to access the on-screen bar.
2
Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
3
Press rt to select the desired option, then press ENTER.
NORMAL : Normally select this option.
CINEMA : Suitable for a movie disc, etc.
SHARP : Clearer, sharper-edged picture when viewing images with
lots of flat, same-coloured surfaces such as cartoons.
SOFT : Select this option when too much noise appears.
To clear the on-screen bar
Press ON SCREEN.
Setting The Progressive Mode
You can obtain optimal picture quality by selecting whether the
content on the disc is processed by field (video source) or by frame
(film source).
1
Set the unit to the progressive scan mode. ( ੬ pg. 80)
2
Press ON SCREEN twice to access the on-screen bar.
3
Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
4
Press rt to select the desired option, then press ENTER.
AUTO 1 : Used to play a disc containing both video and film source
materials. This system recognises the source type (video or film)
of the current disc according to the disc information. Normally
select this option.
AUTO 2 : Almost the same as the “AUTO 1”, but the processing of
the scenes with movement is different. Select “AUTO 1” or
“AUTO 2” to your preference.
FILM : Suitable for playing back a progressive scanned film source
disc.
VIDEO : Suitable for playing back a video source disc. The outlines
on the played back pictures will be soft.
To clear the on-screen bar
Press ON SCREEN.
NOTE:
When the progressive mode is set, be sure to set “L-1 OUTPUT” to
“COMPONENT”. (
੬ pg. 44) Progressive scan is output only from
[COMPONENT VIDEO OUT] connector.
DVD-VIDEO
: :
AUTO 1
TIME ENTER
TIME
TIME
TIME
TIME
TIME
Press 1 Press 2
Press 0 Press 5
DVD-VIDEO AUTO 1
DVD-VIDEO AUTO 2
MV5SEK_00.book Page 57 Wednesday, August 31, 2005 7:58 PM