Samsung CLP-775 SERIES - Manual (Page 33)

Network setup_ 33
4. Select the Wireless Setting and Installation option.
• Install Now: If you have already set up the wireless network,
click this button to install the machine’s driver to use the wireless
network machine. If you have not set up the wireless network,
click the Wireless Setting and Installation button to set up the
wireless network before you click this button.
• Wireless Setting and Installation: Configure the wireless
network settings of your machine with a USB cable then install
the machine driver. This is only for users who have not set up the
wireless connection before.
5. Read the License Agreement, and select I accept the terms of the
License Agreement. Then, click Next.
6. The software searches the wireless network.
If the search has failed, you may check if the USB cable is
properly connected between the computer and machine, and
follow the instructions on the window.
7. After searching, the window shows the wireless network devices.
Select the name (SSID) of the access point you are using and click
Next.
If you cannot find the network name you want to choose, or if
you want to set the wireless configuration manually, click
Advanced Setting.
• Enter the wireless Network Name: Enter the SSID of
access point you want (SSID is case-sensitive).
• Operation Mode: Select Infrastructure.
• Authentication: Select an authentication type.
Open System: Authentication is not used, and encryption
may or may not be used, depending on the need for data
security.
Shared Key: Authentication is used. A device that has a
proper WEP key can access the network.
WPA Personal or WPA2 Personal: Select this option to
authenticate the print server based on WPA Pre-Shared
Key. This uses a shared secret key (generally called Pre-
Shared Key pass phrase) which is manually configured on
the access point and each of its clients.
• Encryption: Select the encryption (None, WEP64,
WEP128, TKIP, AES, TKIP AES).
• Network Key: Enter the encryption network key value.
• Confirm Network Key: Confirm the encryption network
key value.
• WEP Key Index: If you are using WEP Encryption, select
the appropriate WEP Key Index.
The wireless network security window appears when the
access point has security settings.
The wireless network security window appears. The window
may differ according to its security mode: WEP, or WPA.
• WEP
Select Open System or Shared Key for the authentication
and enter the WEP security key. Click Next.
WEP (Wired Equivalent Privacy) is a security protocol
preventing unauthorized access to your wireless network.
WEP encrypts the data portion of each packet exchanged
on a wireless network using a 64-bit or 128-bit WEP
encryption key.
• WPA
Enter the WPA shared key and click Next.
WPA authorizes and identifies users based on a secret key
that changes automatically at regular intervals. WPA also
uses TKIP (Temporal Key Integrity Protocol) and AES
(Advanced Encryption Standard) for data encryption.
8. The window shows the wireless network settings and checks if the
settings are correct. Click Next.
• For the DHCP method
If the IP address assignment method is DHCP, check if DHCP is
shown in the window. If it shows Static, click Change TCP/IP to
change the assignment method to DHCP.
• For the Static method
If the IP address assignment method is Static, check if Static is
shown in the window. If it shows DHCP, click Change TCP/IP to
enter the IP address and other network configuration values for
the machine. Before entering the IP address for the machine, you
must know the computer’s network configuration information. If
the computer is set to DHCP, you must contact the network
administrator to get the static IP address.
For example:
If the computer’s network information is as shown below:
- IP address: 169.254.133.42
- Subnet Mask: 255.255.0.0
Then, the machine’s network information should be as follows:
- IP address: 169.254.133.43
- Subnet Mask: 255.255.0.0 (Use the computer’s subnet
mask.)
- Gateway: 169.254.133.1
9. When the wireless network setting is completed, disconnect the USB
cable between the computer and machine. Click Next.
10. The Wireless Network Setting Complete window appears.
Select Yes if you accept the current settings and continue the setup
procedure.
Select No if you want to return to the beginning screen.
Then, click Next.
11. Click Next when the Confirm Printer Connection window appears.
12. Select the components to be installed. Click Next.
13. After selecting the components, you can also change the machine
name, set the machine to be shared on the network, set the machine
as the default machine, and change the port name of each machine.
Click Next.
14. After the installation is finished, a window asking you to print a test
page appears. If you want to print a test page, click Print a test
page.
Otherwise, just click Next and go to step 16.