Samsung SCC-ZM395N - Manual (Page 29)

Version 1.1
- 29 -
* When BACKLIGHT is BLC, the MASK AREA is disable
* The Mask area only can be used in AUTO mode
* The area maximum length is 239 ( 0xEF) ; maximum width is 188 (0xBC)
If you set the area is larger than the maximum area, it only can display the maximum area
* The area minimum length is 120 (0x78) ; minimum width is 94 (0x5D)
If you set the area is smaller than the minimum area, it only can display the minimum area
WHITE
BALANCE
DAY/NIGHT state
select
02H 07H 10H 00H **H
00H: Day
01H: Night
O
DAY MODE 02H 07H 00H 00H **H
00H: ATW1, 01H: ATW2, 02H: AWC
03H: 3200K, 04H: 5600K
O
DAY RED 02H 07H 01H 00H **H 00H~40H: -32~+32 O
DAY BLUE 02H 07H 01H 01H **H 00H~40H: -32~+32 O
DAY AWC R-GAIN 02H 07H 02H **Hi **Low 000H~3FFH: 0~1023 O
DAY AWC B-GAIN 02H 07H 03H **Hi **Low 000H~3FFH: 0~1023 O
DAY AWC shot 02H 07H 04H 00H 01H O
NIGHT MODE 02H 07H 05H 00H **H
00H: ATW1, 01H: ATW2, 02H: AWC
03H: 3200K, 04H: 5600K, 05H: OFF
O
NIGHT BRIGHTNESS 02H 07H 0AH 00H **H 00H: LOW, 01H: MID, 02H: HIGH O
NIGHT RED 02H 07H 06H 00H **H 00H~40H: -32~+32 O
NIGHT BLUE 02H 07H 06H 01H **H 00H~40H: -32~+32 O
NIGHT AWC R-GAIN 02H 07H 07H **Hi **Low 000H~3FFH: 0~1023 O
NIGHT AWC B-GAIN 02H 07H 08H **Hi **Low 000H~3FFH: 0~1023 O
NIGHT AWC shot 02H 07H 09H 00H 01H O
* When AGC is OFF or FIX cannot select NIGHT mode
* After sending the DAY/NIGHT state selection command, the screen of camera changes according to
the selected state that do not change according to the current state.
When sending the save command, the screen changes depending on the current state.
FOCUS
FOCUS 02H 08H 00H 00H **H 00H:ONEAF, 01H:AF, 02H:MF O
FOCUS LIMIT 02H 08H 01H 00H **H 00H: 5 cm, 01H: 20 cm O
FOCUS FAR 01H 01H 00H 00H 00H FOCUS FAR X
FOCUS NEAR 01H 02H 00H 00H 00H FOCUS NEAR X
FOCUS STOP 01H 03H 00H 00H 00H FOCUS STOP O
FOCUS DIRECT 80H 00H 00H **Hi **Low 0x7526 ~ 0x8900 X
* FOCUS STOP command must be used after sending FOCUS NEAR and FOCUS FAR command.
ZOOM
ZOOM SPEED 02H 1DH 00H 00H **H 0H~03H: 1~4 O
ZOOM TELE 01H 20H 00H 00H 00H ZOOM TELE X
ZOOM WIDE 01H 40H 00H 00H 00H ZOOM WIDE X
ZOOM STOP 01H 30H 00H 00H 00H ZOOM STOP O
ZOOM DIRECT 10H 00 00 **Hi **Low Value : 0x80E6 ~ 0x9B00 X
ZOOM RATIO
DISPLAY
02H 1DH 01H 00H **H 00H: OFF, 01H: ON O
* ZOOM STOP command must be used after sending ZOOM WIDE and ZOOM TELE command.
DIGITAL
ZOOM
DIGITAL ZOOM
RATIO (MAX.)
02H 0EH 01H 00H **H
DZOOMDATA_OFF(x1) 00H
DZOOMDATA_x2 01H
DZOOMDATA_x3 02H
DZOOMDATA_x4 03H
DZOOMDATA_x5 04H
DZOOMDATA_x6 05H
DZOOMDATA_x7 06H
DZOOMDATA_x8 07H
DZOOMDATA_x9 08H
DZOOMDATA_x10 09H
DZOOMDATA_x11 0AH
DZOOMDATA_x12 0BH
O
DIGITAL ZOOM
DIRECT
64H 00H 00H 00H *H DZOOM value 0x00H ~ 0xEBH X
* This function is disabled when D-ZOOM OFF.
This value is depending on the D-ZOOM ratio, D-ZOOM ratio of the max DZOOM value is different.
* If DZOOM DIRECT command can be sent, the zoom operates optical zoom max. value automatically
and operates to the DZOOM.