Sony PDW-F30 - Manual (Page 87)

87
System Menu
C
h
ap
te
r 6
M
enu
s
LEVEL SELECT
[> Level Sel]
REF LEVEL [>> REF Level]:
Specify the reference
level (headroom) for
audio signals recorded to
disc.
* –20dB [>>> –20dB]
–18dB [>>> –18dB]
–16dB [>>> –16dB]
–12dB [>>> –12dB]
OUTPUT LEVEL [>> Out
Level]: Select the analog
audio output reference
level.
* +4dB [>>> +4dB]
0dB [>>> 0dB]
–3dB [>>> –3dB]
–6dB [>>> –6dB]
INT AUDIO SG [> Audio SG]: Select the operation of the
internal audio test signal generator.
SILENCE [>> silence]: Silent signal
*
1kHz SINE [>> 1kHz]: 1-kHz, –20 dB FS sine wave signal
SHUTTLE MUTING [> Shtl muting]: Set the audio muting
conditions during shuttle playback.
* OFF [>> OFF]: Do not perform muting.
ON [>> FULL]: Perform muting.
EDIT POINT [> Edit Point]: Specify the type of editing for
audio signals.
CUT [>> Cut]: Cut editing (Discontinuity in audio signal may
result at the editing point, causing noise during playback.)
* FADE [>> Fade]: Fade in and fade out
DV OUT MODE [> DV out mod]: Select the audio output
mode of the S400 connector.
4ch [>> 4ch]: 12 bit/32 kHz/4ch
*
2ch [>> 2ch]: 16 bit/48 kHz/2ch
INTERFACE SELECT [Interface]: Settings related to
interfaces Description
D-SUB OUTPUT [> D-SUB Out]: Select the format of the
signal output from the MONITOR connector.
XGA(SYSTEM) [>> XGA(SYS)]: Set to XGA monitor output
(according to system frequency).
* XGA(60Hz) [>> XGA(60Hz)]: Set to XGA monitor output
(fixed at 60 Hz).
YPbPr [>> YPbPr]: Y/R–Y/B–Y component video signals
AUDIO OUTPUT [> Audio Out]: Select the channels for audio
output from the AUDIO OUTPUT 1/3 and 2/4 connectors.
* CH1/CH2 [>> CH1/CH2]: Output channel 1 to the AUDIO
OUTPUT 1/3 connector and channel 2 to the AUDIO
OUTPUT 2/4 connector.
CH3/CH4 [>> CH3/CH4]: Output channel 3 to the AUDIO
OUTPUT 1/3 connector and channel 4 to the AUDIO
OUTPUT 2/4 connector.
REMOTE I/F [> Remote I/F]: Select how to perform remote
control, when the remote control switch is set to
REMOTE.
i.LINK [>> i.LINK]: Use the S400 connector.
*
9PIN/RS-232C [>> 9P/232C]: Use either the REMOTE(9P)
connector or the RS232C connector, depending on the
setting of the remote connector selector switch.
9PIN(PARA)[>> Para Run]: Use the REMOTE(9P) connector
to connect several PDW-F30 units and perform remote
control from one of them specified as the parent.
BAUDRATE [> BaudRate]: Select the communications speed
(bps) of the RS232C connector.
* 9600 [>> 9600]
19200 [>> 19200]
38400 [>> 38400]
57600 [>> 57600]
115200 [>> 115200]
i.LINK MODE [> i.LinkMode]: Select the type of connection
for the S400 connector.
* AV/C [>> AV/C]: AV/C connection.
FAM(PC REMOTE) [>> FAM]: FAM connection.
NETWORK ENABLE [> Network En]: Select the positions of
the remote control switch which enable access to the
network.
* NETWORK [>> Network]: Only when the switch is set to
“NETWORK”.
NETWORK&RS-422A[>> Net&Rmt]: Only when the switch is
set to “NETWORK”, or when the switch is set to
“REMOTE” and the menu item REMOTE I/F is set to
“9PIN/RS232”.
AUDIO CONTROL [Audio]: Settings related to audio
control Description
IN OUT