Sony DVS-V3232B/V3232M - Manual (Page 115)

5-43
ROUTING SWITCHER SYSTEM (E)
5-2. Setting Items of the Secondary Station
SONY ROUTING SYSTEM SETUP MENU BKS-R3205 V3.10 STATION NUMBER 11
SET PANEL STATUS
PANEL MODE = 1
1:STAND ALONE 2:MOTHER
SET SOURCE OR DESTINATION ASSIGNMENT
KEY 1- 8 = S KEY 9-16 = S
KEY 17-24 = S KEY 25-32 = S
S:SOURCE D:DESTINATION
SET BLOCK NUMBER=3
MOTHER STATION BLOCK LIST
BLOCK 1 = STATION 11 | BLOCK 6 = .......
BLOCK 2 = STATION 5 | BLOCK 7 = .......
BLOCK 3 = STATION 2 | BLOCK 8 = .......
BLOCK 4 = STATION 3 | BLOCK 9 = .......
BLOCK 5 = ....... | BLOCK10 = .......
Ctrl-E:MENU Ctrl-D:RETURN
SONY ROUTING SYSTEM SETUP MENU BKS-R3206 V3.10 STATION NUMBER 2
SET PANEL STATUS
PANEL MODE = 2
1:STAND ALONE 2:MOTHER
PANEL LAYOUT = 2
1: KEY + NUMBER SELECT MODE
2: SOURCE DIRECT SELECT MODE
SET BLOCK NUMBER = 2
MOTHER STATION BLOCK LIST
BLOCK 1 = STATION 11 | BLOCK 6 = .......
BLOCK 2 = STATION 5 | BLOCK 7 = .......
BLOCK 3 = STATION 2 | BLOCK 8 = .......
BLOCK 4 = STATION 3 | BLOCK 9 = .......
BLOCK 5 = ....... | BLOCK10 = .......
Ctrl-E:MENU Ctrl-D:RETURN
Example of Setting Screen (BKS-R3205)
Example of Setting Screen (BKS-R3206)
Z : SET PANEL STATUS (BKS-R1607/R1608/
R3209/R3210/R3216/R1617/R1618/R3219/
R3220/R1621)
Purpose
This is the function to set the various modes of the remote
control unit. In the models corresponding this menu as
shown above the multiple units can be connected in order
to expand the number of sources and destinations which
can be controlled simultaneously. Setting the mother panel
and the daughter panels is performed from this menu.
(Maximum ten mother panels can be set.)
Contents to be set are shown below.
DISPLAY MODE
STATUS = Indicates the status of the primary station’s
crosspoint table.
PROMPT = The depressed button lit immediately.
PROTECT MODE
ON AIR = Switching is performed from that panel even
after protected.
NORMAL = Switching is prohibited after protected.
FLEXIBLE = Switching is prohibited after protected.
However, protections by other stations can
be released.
*1
FLEX & OA =Uses the functions of both 1 : ON AIR
and 3 : FLEXIBLE. *1
PHANTOM PROTECT
PART PROT = The phantoms that are not protected are
switched.
FULL PROT = All phantoms cannot be switched when
even one phantom on which protect is
set to on, is included.
BUTTON LINK = All phantoms cannot be switched
when the protect button is set to on.
PANEL MODE
STAND ALONE = Stand alone panel
MOTHER = Mother panel
DAUGHTER = Daughter panel
PANEL LAYOUT *2
TYPE + NUM. = Selection of X-Y
DIRECT = Direct selection *3
BPS = Source button selection *1
KEYPAD = Description selection *1
(Only BKS-R3216 is valid.)
* 1 : It is only applicable to BKS-R3216/R1617/R1618/R3219/R3220/R1621.
* 2 : It is only applicable to BKS-R3210/R3216.
* 3 : BKS-R1607/R1608/R3209/R3210