Shark V1730 - Manual (Page 7)

5
CLEANING THE DUST CONTAINER
To achieve the best performance, empty the dust container after each use.
1. Pull the dust
container
straight out from
the side.
(Fig. 6)
2. Empty dust
container
contents. (Fig. 7)
If desired- you
may rinse with
water to clean
the dust
container – but
dry thoroughly
before replacing
on the sweeper.
3. Replace dust container on cordless
sweeper.
4. Periodically remove the brush cover on
the front of the cordless sweeper and
remove any build up of lint, hair or fiber
on the rotating brush. To remove the
cover - grip the
cover from the
bottom, pull out
and upward until
the cover
unlocks from the
side slots and
tabs located on
the top of the
sweeper. (Fig. 8)
CAUTION: Do not accidentally turn unit on while cleaning.
Do not clean while unit is charging.
CHARGING THE CORDLESS SWEEPER
1. Connect the charger plug to the charging jack or hole on the back of the
sweeper. Plug the the charging adapter into the wall outlet. (120V., 60Hz.) Use only
TechWorld Charger AD-1215-UL8. (Fig. 9)
2. This cordless sweeper is powered by Ni-Cd batteries. Before first use, they must be
charged for a minimum of 20 hours.
3. When recharging the unit, the "On/Off" switch must be in
the "OFF" position.
4. The charging light indicator on the top of the sweeper
will flash to indicate that the sweeper is properly
charging.
5. The charging indicator light will stop flashing when
the battery is fully charged.
6. To recharge, repeat step #1 above. Charging times will
vary depending upon the amount of usage between
charging cycles.
Note: Your sweeper is highly advanced and has electronic controls that optimize the
cleaning ability and durability of the sweeper. Please review the following instructions
carefully to ensure that all features are utilized for best performance.
1. When charging the sweeper, the battery/charge indicator will flash until the unit is
fully charged and then turn steady.
2. When running the unit, the battery indicator will start as solid green, change to solid
orange when approximately 70% of the battery life is used, and blink orange when
in need of charging. The sweeper will prevent the batteries from being deeply
discharged and will indicate this by the battery indicator flashing, the headlights
flashing, and the sweeper will stop operating. This is normal and all that needs done is
to recharge the sweeper fully.
3. When recharging from being fully discharged, the unit must charge for 1 hour
minimum before it’s electronics will allow the unit to operate again.
Fig. 6
Fig. 7 Fig. 8
Fig. 9
48
UTILISATION DE LA BALAYEUSE À MAIN SANS FIL
Avant de commencer:
Votre balayeuse à main sans fil exige très peu d’assemblage. Retirez-la de la boîte et
familiarisez-vous avez toutes ses pièces indiquées dans l’illustration des pièces (p.47)
Ceci vous aidera à assembler et à utiliser la balayeuse à main sans cordon.
ATTENTION : Les appareils électriques ou électroniques
ne doivent pas être rangés dans des endroits très chauds et
humides et ne doivent pas y être exposés. Ne rangez pas la
balayeuse près des cuisinières, radiateurs, fournaises ou
dans la salle de bain.
1. Avant l’usage initial, chargez la balayeuse pendant 20 heures. La balayeuse
fonctionnera convenablement lorsque ses piles seront entièrement chargées.
Lorsque pleinement chargée, la balayeuse fonctionnera pendant environ 20 à 25
minutes, selon le type d’usage (exemple – comptoirs/tables ou meubles).
2. Appuyez sur le commutateur pour mettre la balayeuse en marche. Pour l’éteindre,
appuyez encore une fois sur le commutateur (fig. 1).
REMARQUE: n’utilisez pas la balayeuse sans que son plateau à poussière soit
en place.
Fig. 1
Commutateur