ST & T UPSD3212C - Manual (Page 25)

25/163
uPSD3212A, uPSD3212C, uPSD3212CV
Table 14 shows the list of conditional jumps avail-
able to the uPSD321x Devices user. All of these
jumps specify the destination address by the rela-
tive offset method, and so are limited to a jump dis-
tance of -128 to +127 bytes from the instruction
following the conditional jump instruction. Impor-
tant to note, however, the user specifies to the as-
sembler the actual destination address the same
way as the other jumps: as a label or a 16-bit con-
stant.
There is no Zero Bit in the PSW. The JZ and JNZ
instructions test the Accumulator data for that con-
dition.
The DJNZ instruction (Decrement and Jump if Not
Zero) is for loop control. To execute a loop N
times, load a counter byte with N and terminate the
loop with a DJNZ to the beginning of the loop, as
shown below for N = 10:
MOV COUNTER,#10
LOOP: (begin loop)
•
•
•
(end loop)
DJNZ COUNTER, LOOP
(continue)
The CJNE instruction (Compare and Jump if Not
Equal) can also be used for loop control as in
Ta-
ble 9., page 21 . Two bytes are specified in the op-
erand field of the instruction. The jump is executed
only if the two bytes are not equal. In the example
of
Table 9., page 21 Shifting a BCD Number One
Digits to the Right, the two bytes were data in R1
and the constant 2Ah. The initial data in R1 was
2Eh.
Every time the loop was executed, R1 was decre-
mented, and the looping was to continue until the
R1 data reached 2Ah.
Another application of this instruction is in “greater
than, less than” comparisons. The two bytes in the
operand field are taken as unsigned integers. If the
first is less than the second, then the Carry Bit is
set (1). If the first is greater than or equal to the
second, then the Carry Bit is cleared.
Machine Cycles
A machine cycle consists of a sequence of six
states, numbered S1 through S6. Each state time
lasts for two oscillator periods. Thus, a machine
cycle takes 12 oscillator periods or 1µs if the oscil-
lator frequency is 12MHz. Refer to
Figure
14., page 26 .
Each state is divided into a Phase 1 half and a
Phase 2 half. State Sequence in uPSD321x Devic-
es shows that retrieve/execute sequences in
states and phases for various kinds of instructions.
Normally two program retrievals are generated
during each machine cycle, even if the instruction
being executed does
not require it. If the instruc-
tion being executed does not need more code
bytes, the CPU simply ignores the extra retrieval,
and the Program Counter is not incremented.
Execution of a one-cycle instruction (
Figure
14., page 26 ) begins during State 1 of the machine
cycle, when the opcode is latched into the Instruc-
tion Register. A second retrieve occurs during S4
of the same machine cycle. Execution is complete
at the end of State 6 of this machine cycle.
The MOVX instructions take two machine cycles
to execute. No program retrieval is generated dur-
ing the second cycle of a MOVX instruction. This
is the only time program retrievals are skipped.
The retrieve/execute sequence for MOVX instruc-
tion is shown in
Figure 14., page 26 (d).
Table 14. Conditional Jump Instructions
Mnemonic Operation
Addressing Modes
Dir. Ind. Reg. Imm
JZ rel Jump if A = 0 Accumulator only
JNZ rel Jump if A
≠
0 Accumulator only
DJNZ <byte>,rel Decrement and jump if not zero X X
CJNE A,<byte>,rel Jump if A
≠
<byte> X X
CJNE <byte>,#data,rel Jump if <byte>
≠
#data X X