Kenwood KDC BT948HD - Manual (Page 49)

English |
49
Display Overview
“SMS Inbox” Display the received short message.
Refer to <SMS (Short Message Service)>
(page 54) .
“BT Settings”
“Pairing”
“Device Regist.” Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth device>
(page 50) .
“Phone
Selection”
Select a cell-phone connection.
Refer to <Selecting the Bluetooth device You
Wish to Connect> (page 51) .
“SPCL DVC
Select”
Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth device>
(page 50) .
“Device Delete” Cancel registration of the Bluetooth device.
Refer to <Deleting a Registered Bluetooth
device> (page 52) .
“SMS Download” Download a short message.
Refer to <Downloading the SMS> (page 54) .
“Voice Tag” Registers voice for voice recognition and voice
to select the Phone number category in Phone
book.
- Adding a Voice Dialing Command (page 52)
- Setting a Voice Command for Category (page
53)
“Detailed Setup” Move to detailed item.
“PIN Code Edit” Specify the PIN code required when registering
this unit using the Bluetooth device.
Refer to <Registering PIN Code> (page 51) .
“Auto Answer” Answer a call automatically after lapse of the
preset time interval for automatic answer.
“OFF”/ “0s” – “8s” – “99s”
“Auto
Reconnect”* 2
Automatically reconnects the selected
Bluetooth device when radio wave becomes
strong enough, even after it is disconnected.
“ON”/ “OFF”
✍ When this function is enabled, the
Bluetooth device is reconnected
even if “Phone Selection” is selected
to select a cell-phone connection.
To cancel the Bluetooth connection,
select OFF to disable this function.
“Bluetooth HF” You can specify output speakers for hands-free
voice communication.
“FRONT”: Outputs voice from the front
speakers.
“ALL”: Outputs voice from the front and rear
speakers.
“Call Beep” You can output a beep from the speaker when
a call comes in.
“ON”: Beep is heard.
“OFF”: Beep is canceled.
“BT F/W Update” Display the version of the firmware of this unit.
“Mic Gain” Adjust the sensitivity of the microphone for a
telephone call. Adjust the voice of caller. Setting
to “+” increases the voice volume.
“–3” – “0” – “+3”
“NR Level” Reduce the noises generated by surrounding
environment without changing the microphone
volume. Adjust the voice of caller when it is
not clear. Setting to “+” increases the noise
reduction.
“–3” – “0” – “+3”
“Echo Cancel LV“ Adjust the level of echo cancellation. Setting to
“+” increases the echo cancel reduction.
“–2” – “0” – “+2”
( : Factory setting)
4
Make a setting
• When the “
PUSH ” icon is displayed (at the
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
• When the “ PUSH ” icon is not displayed
Press the [ 4] or [¢] button to select a
setting value.
5
Exit BT Settings mode
Press the [
] button.
Remarks
• “Auto Answer” (Setting the Time Interval for Automatic
Answer)
This function automatically answers (responds to) a call
after lapse of the preset time interval for automatic answer.
“OFF” : Does not answer the phone call automatically.
“0” : Automatically answers the phone call at once.
“1s” – “99s” : Automatically answers the phone call after
lapse of 1 – 99 seconds.
⁄
• If the time set in the cell-phone is shorter than that set in
the unit, the former will be used.
• This function does not work for call waiting.
• “Bluetooth HF” (Setting up the Voice Output Speakers)
Select the speaker which is further from the microphone in
order to prevent howling or echoes.
• “BT F/W Update” (Displaying the Firmware Version)
Display the version of the firmware of this unit.
For how to update the firmware, access our web site.
http://www.kenwood.com/cs/ce/bt/