Kenwood VZ-7000P - Manual (Page 4)

English
4
Safety Precautions
To prevent injury and/or fire, take the following
precautions:
• Ensure that the unit is securely installed. Otherwise it
may fly out of place during collisions and other jolts.
• When extending the ignition, battery or ground wires,
make sure to use automotive-grade wires or other
cables with an area of 0.75mm
2 (AWG18) or more to
prevent wire deterioration and damage to the wire
coating.
• To prevent short circuits, never put or leave any
metallic objects (e.g., coins or metal tools) inside the
unit.
• If the unit starts to emit smoke or strange smells, turn
off the power immediately and consult your Kenwood
dealer.
• Do not touch the liquid crystal fluid if the LCD is
damaged or broken due to shock. The liquid crystal
fluid may be dangerous to your health or even fatal.
If the liquid crystal fluid from the LCD contacts your
body or clothing, wash it off with soap immediately.
To prevent damage to the machine, take the
following precautions:
• Make sure to ground the unit to a negative 12V DC
power supply.
• Do not open the top or bottom covers of the unit.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
• Do not subject the faceplate to excessive shock, as it
is a piece of precision equipment.
• When replacing a fuse, only use a new one with the
prescribed rating. Using a fuse with the wrong rating
may cause your unit to malfunction.
• To prevent short circuits when replacing a fuse, first
disconnect the wiring harness.
• Do not use any screws except for the ones provided.
The use of improper screws might result in damage to
the main unit.
• You cannot view video pictures whilst the vehicle is
moving. To enjoy TV/video pictures, find a safe place to
park and engage the parking brake.
• If you experience problems during installation, consult
your Kenwood dealer.
• If the unit does not seem to be working right, try
pressing the reset button first. If that does not solve
the problem, consult your Kenwood dealer.
• When a center unit is connected, press the reset
button of the center unit once. Refer to the instruction
manual of the center unit for the location of the reset
button.
• If a center unit is connected, do not use the reset
button of this unit, but press the reset button of the
center unit.
Cleaning the Unit
If the front panel gets dirty, turn off the power and wipe
the panel with a dry silicon cloth or soft cloth.
Do not wipe the panel with a stiff cloth or a cloth
dampened by volatile solvents such as paint thinner and
alcohol. They can scratch the surface of the panel and/or
remove the indicator letters.
Screen brightness during low temperatures
When the temperature of the unit falls such as during
winter, the liquid crystal panel's screen will become
darker than usual. Normal brightness will return after
using the monitor for a while.
Loading and Replacing the Batteries for the
Remote
Do not set the remote on hot places such as above the
dashboard.
Loading and Replacing the Batteries
1. Use two "AAA" batteries:
Slide the cover while pressing
downwards to remove it as illustrated.
2. Insert the batteries with the ª and ·
poles aligned properly following the
illustration inside the case.
Store unused batteries out of the reach of children.
Contact a doctor immediately if the battery is
accidentally swallowed.
• The provided batteries are intended for use in
operation checking, and their service life may be short.
• When the remote controllable distance becomes short,
replace both of the batteries with new ones.
IMPORTANT INFORMATION
• The center units that can be operated on the touch
panel of this unit are as follows (as of April, 2002):
KDC-9020R,KDC-MPV7020,KDC-6020,KDC-Z939,
KDC-Z838,KDC-Z737 and KRC-Z965
• To connect a disc changer/CD player, a center unit and
KCA-S210A are necessary. Refer to the instruction
manual of KCA-S210A for the connection method.
• If there is the “O-N” switch on a disc changer/CD
player to be connected, set the switch to the “N”.
NOTE
2WARNING
2CAUTION
2CAUTION
NOTE
2CAUTION
2WARNING
Reset button
C-01177(H)-Eng 02.3.20 3:12 PM Page 4