Welding power source selection, Operation – Lincoln Electric SVM143-A User Manual
Page 21
B-3
OPERATION
B-3
DH-10
SINGLE HEADS:
For K1563-1 (LN-10 Boom) with 35-500 IPM (0.89-
12.7 m/m) Low Speed Ratio set S2 DIP Switches as
follows:
For K1563-1 (LN-10 Boom) with 50-750 IPM (1.25-
19.0 m/m) High Speed Ratio set S2 DIP Switch as
follows: (initial factory setting)
For K1563-2 (LN-10 Boom) with 55-825 IPM (1.40-
21.0 m/m) Low Speed Ratio set S2 DIP Switch as
follows:
For K1563-2 (LN-10 Boom) 80-1250 IPM (2.00-31.8
m/m) High Speed Ratio set S2 DIP Switch as fol-
lows: (initial factory setting)
For K679-1 (Single Head Boom) with 50-770 IPM
(1.27-19.5 m/m) Low Speed Ratio set S2 DIP Switch
as follows:
For K679-2 (Single Head Boom) with 80-1200 IPM
(2.00-30.5 m/m) High Speed Ratio set S2 DIP
Switch as follows:
NOTE: Any single drive may be connected to the
Head 1 or Head 2 connector. Both settings are con-
figured the same way.
HEAD 1
S2
ON
S2
1
2
3
4
5
6
7
8
HEAD 2
HEAD 1
S2
ON
S2
1
2
3
4
5
6
7
8
HEAD 2
HEAD 1
S2
ON
S2
1
2
3
4
5
6
7
8
HEAD 2
HEAD 1
S2
ON
S2
1
2
3
4
5
6
7
8
HEAD 2
HEAD 1
S2
ON
S2
1
2
3
4
5
6
7
8
HEAD 2
HEAD 1
S2
ON
S2
1
2
3
4
5
6
7
8
HEAD 2
Welding Power Source Selection
The DH-10 Control is set up for proper presettable
weld voltage control by setting S1 DIP switches (1 to
4) as appropriate per the following information for the
welding power source being used:
CV-250/CV 300-I:
CV-300/CV 400-I:
CV-400/CV 500-I:
CV-655/DC-655: (initial factory setting)
DC-250:
DC-400:
DC-600:
DC-650 PRO:
DC-1000:
Security
Pwr Sources
M 4
S1
ON
S1
1
2
3
4
5
6
7
8
Security
Pwr Sources
M 4
S1
ON
S1
1
2
3
4
5
6
7
8
Security
Pwr Sources
M 4
S1
ON
S1
1
2
3
4
5
6
7
8
Security
Pwr Sources
M 4
S1
ON
S1
1
2
3
4
5
6
7
8
Security
Pwr Sources
M 4
S1
ON
S1
1
2
3
4
5
6
7
8
Security
Pwr Sources
M 4
S1
ON
S1
1
2
3
4
5
6
7
8
Security
Pwr Sources
M 4
S1
ON
S1
1
2
3
4
5
6
7
8
Security
Pwr Sources
M 4
S1
ON
S1
1
2
3
4
5
6
7
8
Security
Pwr Sources
M 4
S1
ON
S1
1
2
3
4
5
6
7
8