LG STB1000 - Manual (Page 44)

44 206-4147
Installer Menu (Cont.)
Installer Menu Items 073 through 119
Menu
Item
Function Value Range Default Value Brief Description of Function and Comments
073 CH NOT AVBLE 0 / 1 0
If set to 1 and Channel Override is 0, “NOT AVAILABLE” message is displayed
when directly accessing a channel not in the favorite Channel List.
075 REVERT CH 0 / 1 0 If set to 1 and loss of MPI communication occurs, STB tunes to Start Channel.
078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.
079 UPN MSB-1 0 ~ 255 0 User programmable number, most significant byte - 1.
080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 2.
081 UPN LSB 0 ~ 255 0 User programmable number, least significant byte.
082 CHKSM ERROR 0 / 1 1 Enforces rigid MPI checksum.
083 HANDSHK TIME 0 ~ 5 5
Relaxes MPI timing to be compatible with PC-based Windows-
controlled systems.
084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block permanent.
087 REAR RGB EN. 0 / 1 / 17 1
Dependent on item 093 RJP AVAILABLE setting. Set to 0 to disable RGB input.
Set to 1 to enable RGB input. Set to 17 for Auto Configure.
088 EN NOISE MUTE 0 / 1 1 If set to 1, audio is muted if no signal is present.
090 KEY LOCK 0 / 1 1 If set to 1, keyboard is locked out, IR is still functional.
091 YPrPb2 EN 0 / 1 1 Set to 1 to enable HDMI 2 input.
093 RJP AVAILABLE 0, 1, 2, 5, 6 0
Set to 0 to disable. Set to 1, 2, 5, or 6 for HDMI or DVI Mode. (See
detailed descriptions.)
094 SAP MENU EN 0 / 1 1
Set to 0 to disable feature on Function Menu. Set to 1 to enable feature on
Function Menu.
096 DEF. ASP. RATIO 0 ~ 4 2 Sets default aspect ratio at power up. See detailed descriptions and item 106.
102 ATSC BAND 0 ~ 4 4 Selects ATSC band.
103 ATSC TUNE MODE 0 / 1 1 Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.
104 START MINOR CH 0 ~ 255 0 Selects Minor Start Channel. Set to 0 for NTSC.
106 ASP RATIO LOCK 0 / 1 0
To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on
power cycle.
108 PANEL COM 0 ~ 3 2 Sets display panel baud rate: 0 = 1200, 1 = 2400, 2 = 9600, 3 = 115200
110 PANEL DELAY 0 ~ 15 8 Sets the display panel communication delay time.
111 PANEL VOL PRE 0 ~ 100 79 Preset panel volume to achieve volume levels in parallel with external equipment.
113 PANEL TYPE 0 ~ 4 2 Selects display panel type. (See detailed descriptions.)
116 VIDEO MUTE EN 0 / 1 0 Set to 0 for Normal. Set to 1 for Blank.
117 FACT DEFAULT 0 / 1 0 Set to 0 for Normal. Set to 1 to load presets for all Installer Menu settings.
118 POWER SAVINGS 1 / 3 3
Set to 3 (default—b-LAN module only powered when STB is turned ON), or
set to 1 (b-LAN module is always powered).
119 DATA CHANNEL 0 ~ 135 0
Set to 0 to disable. Set to the RF channel number of the Data Channel for
Pro:Centric or E-Z Installation data. (See detailed descriptions.)