Panasonic DIGA DMR-E75V - Manual (Page 55)

Timer Recording
55
[6] Turn the unit off when you do not play or record
on DVD.
≥If the timer recording is started with keeping the unit turned on,
the unit is not turned off automatically even after the timer
recording is completed.
∫ To release the unit from recording standby
Press [ , TIMER].
The unit turns on and “ ” goes out.
≥Be sure to press [ , TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only if
“ ” is displayed.
∫ To cancel recording when recording has already
begun
Press [ , TIMER].
≥You can also press and hold [∫] on the VHS main unit for more
than 3 seconds to stop recording.
∫ VPS/PDC Function ( l 64)
(This function is not available in Australia.)
If a TV programme starts earlier or later from original schedule,
recording start and stop can synchronize with the actual
broadcasting.
Conditions for correct operation of the VPS/PDC function:
≥The TV station must broadcast VPS/PDC signals.
≥The programme starting time must be set correctly to the starting
time listed in the newspaper/magazine.
To activate the VPS/PDC Function:
In step 3 in the VPS/PDC item, press [ 3, 4] to select
“ON”.
Note
≥“
” flashes for about 5 seconds when the unit cannot go to timer
recording standby (e.g., video cassette with no prevention tab or no
video casette in the cassette compartment).
During a timer recording performed in SP mode, this function
automatically changes the tape speed if the unit determines that the
remaining tape is insufficient to record the entire programme. If the
remaining tape time is still not sufficient even in LP mode, the
programme cannot be recorded to the end.
≥This function cannot change the recording speed to the EP mode
for PAL system.
≥This function may not work correctly when you record programmes
in NTSC system.
≥The tape length must be set correctly. ( l 56)
≥Some tapes may not work correctly.
≥If the tape speed changes during a timer recording, some brief
picture distortion occurs at the point.
[1] Press [PROG/CHECK].
[2] Press [ 3, 4] to select the programme.
[3] Press [ ¢, CANCEL/RESET] to delete,
or press [ENTER] to change.
≥You cannot change or delete programmes that are currently
recording.
≥The timer recording setting screen appears.
≥To continue deleting programmes steps 2–3.
[4] If you pressed [ENTER] in step 3,
Press [ 3, 4, 2, 1] to change and press
[ENTER].
≥To continue changing programmes steps 2–4.
[5] Press [ , TIMER].
≥“ ” lights on the unit’s display.
The timer recording standby mode is activated on VHS
(“ ” lights on the VHS unit’s display). However, the unit may
not be turned off automatically.
[6] Turn the unit off when you do not play or record
on DVD.
≥If the timer recording is started with keeping the unit turned on,
the unit is not turned off automatically even after the timer
recording is completed.
For your reference
≥Programmes that failed to record are not deleted, but deleted from
the list at 4 a.m. the day after tomorrow automatically.
Tape Speed Auto Change Function
Check, change or delete programmes
Timer recording
/
- - - - - - - - - / - - - - : - - - - : - - - - - -
- - - - - - - - - / - - - - : - - - - : - - - - - -
- - - - - - - - - / - - - - : - - - - : - - - - - -
ARD 27/7 8:01 15:30 LP - - -
Name Date Start Stop VPS
PDC
1
1/3
VHS
75VGN.book 55 ページ ２００４年７月２１日 水曜日 午前１１時５４分