Panasonic DIGA DMR-E75V - Manual (Page 58)

58
[[DVD/VHS]]
Advanced Operations
[RAM] [DVD-R]
With one stroke of the button, programmes are automatically dubbed
onto the disc
° from the stopping location on the tape.
° The available disc for dubbing from the tape are DVD-RAM and
non-finalized DVD-R.
Preparation
VHS (Recording source)
≥Press [VHS].
≥Insert the video cassette containing the programme to be copied.
( l 50)
≥Stop the tape at the position where you wish to start recording.
≥Press [AUDIO] to select the audio you wish to record.
DVD (Recording target)
≥Press [DVD].
≥Release protection. (disc
l 28, cartridge l 15) [RAM]
≥Insert a disc and confirm there is sufficient empty space for
recording on it. ( l 17, 49)
≥Select the recording mode.
Settings (“TV System” l 45)
≥When dubbing an NTSC tape to the DVD
- Set “TV System” on “Connection” in “SETUP” to “NTSC”.
≥When dubbing a PAL/MESECAM tape to the DVD
- Set “TV System” on “Connection” in “SETUP” to “PAL”.
∫To stop dubbing halfway through
Press [ ∫, STOP].
∫When dubbing is started, the following operations also
start automatically
≥“OSD” on VHS FUNCTIONS ) “OFF” (l 56)
≥Recording channel indication on DVD ) “TP” (l 59)
≥Output to TV ) DVD output
≥The audio mode of the target DVD is fixed to “LR”.
∫Only the following operations are allowed while
dubbing
≥Stopping dubbing by pressing [∫, STOP].
≥Switching the audio mode by pressing [AUDIO]. The audio which
you are hearing is recorded.
∫Dubbing VHS tape with high picture quality
Select “Automatic” on “S-VHS Dubbing Setting” in “SETUP” on DVD.
(
l 44)
≥When performing S-VHS dubbing, “S-VHS” lights on the unit’s
display. ( l 44)
≥Component signal is used for dubbing.
≥“Automatic” is selected as default. Use the unit as it is.
Note
≥You cannot operate for dubbing while timer recording standby on
both DVD and VHS. Cancel the timer recording standby.
≥When “DVD / VHS Output” is set to “Manual” ( l 43), or when VHS
output is selected in starting dubbing, the output is switched to DVD
automatically at the time when dubbing is started.
- When the dubbing is already started, you cannot switch the
output manually.
≥When the dubbing is not started or not executed, the “DUBBING”
indicator blinks for about 7 seconds. Check if the unit is properly
prepared.
≥When a Copy-guarded tape is inserted, the message appears on
the display and the recording stops on the spot.
≥When menu screen appeared on the TV, One Touch Dubbing
cannot start. One Touch Dubbing can perform start, after return
from menu screen.
Dubbing from VHS
∫ One Touch Dubbing (VHS l DVD)
SEARCH REW FF SKIP/INDEX
PLAY STOP PAUSE
FUNCTIONS DIRECT NAVIGATOR
µ
DVD/VHS
CREATE
CHAPTER
TRACKING/V-LOCK
DVD/VHS
CANCEL/RESET INPUT SELECT
DIRECT TV REC
VHS
G-Code
CREATE
CHAPTER
CH
AV
VOLUME
DVD
CH, W, X
DUBBING AUDIO EXT LINK
VHS REC DVD REC REC MODE TIMER
VHS DVD
JET REW
DVD
VHS
1
; ∫
AUDIO
REC MODE
“ DVD
OPEN/CLOSE TIME SLIP
REC CH
/ k1.3
DUBBING VHS DVD
DVD
DUBBING indicator
[1]
While both DVD/VHS are stopped,
Press and hold [ “ DVD, DUBBING] for
3 seconds or more.
≥Check if dubbing starts properly.
≥On the main unit, press [“ DVD].
≥The “DUBBING” indicator on the main unit lights.
≥Dubbing is automatically completed when the tape
reaches to the end or the disc becomes full.
≥When dubbing is completed, a message indicating the
end of dubbing appears on the TV screen and then
disappears a few seconds later.
∫Dividing a programme to be dubbed
In One Touch Dubbing from VHS to DVD, the programme is
divided into titles by index signal (
l 52) detected and then
recorded. You can search desired titles with Direct Navigator’s
Title View (
l 31) after dubbing to DVD.
≥The recording time may become longer than the original title
depending on the number of index signals.
VHS DVD
75VGN.book 58 ページ ２００４年７月２１日 水曜日 午前１１時５４分