Pioneer Elite SC-07 - Manual (Page 24)

Connecting your equipment 03
24
En
Connecting digital audio sources
This receiver has both digital inputs and outputs, allowing you to connect digital audio components for playback and
for making digital recordings.
Most digital components also have analog connections. See Connecting analog audio sources on page 25 if you want
to connect these too.
1 Connect an optical-type 1 digital audio output on
your digital component to the OPTICAL IN 4 (CD-R)
input.
Use an optical cable for the connection.
2 For recording equipment, connect one of the
optical-type DIGITAL outputs to a digital input on the
recorder.
Use an optical cable to connect to the
SOURCE OUT or
ZONE3/SOURCE OUT. 2
About the WMA9 Pro decoder
This unit has an on-board Windows Media™ Audio 9
Professional
3
(WMA9 Pro) decoder, so it is possible to
playback WMA9 Pro-encoded audio using a coaxial or
optical digital connection when connected to a WMA9
Pro-compatible player. However, the connected PC, DVD
player, set-top box, etc. must be able to output WMA9 Pro
format audio signals through a coaxial or optical digital
output.
LAN (10/100)
DIGITAL
SPEAKERS
CAUTION:
SPEAKER IMPEDANCE 6 Ω - 16 Ω .
ATTENTION:
ENCEINTE D'IMPEDANCE DE 6 Ω - 16 Ω .
OPTICAL
RS-232C
HDMI
COAXIAL
COMPONENT VIDEO
ANTENNA
PRE OUT
MULTI CH IN
A
XM
IR
CONTROL
SIRIUS
BD
IN
IN
IN
12 V
TRIGGER
IN
1
IN
2
IN
3
OUT
1
OUT
2
SOURCE
OUT
ZONE3/
SOURCE
OUT
3 1 ASSIGNABLE -
3 1 ASSIGNABLE -
(HDMI
CTRL)
ASSIGNABLE
ASSIGNABLE
(CD-R)
IN 4
(VIDEO1)
IN 3
(DVR1)
IN 2
(TV/SAT)
IN 1
IN 3 (DVR2)
IN 2 (CD)
IN 1 (DVD)
IN 1 IN 2
(OUTPUT
12V
TOTAL
50mA
MAX)
1
2
IN
1
IN
IN
2
OUT
OUT
(DVD)
P R P B Y P R P B Y
P R P B Y (VIDEO1)
IN 3
(VIDEO2)
R
ZONE 2 OUT MONITOR
OUT
PHONO
IN
CD
IN
DVD
IN
TV/SAT
IN
VIDEO1
IN
VIDEO2
IN OUT
DVR1
IN OUT
DVR2
IN OUT IN
CD-R/TAPE
SIGNAL
GND
ZONE 2
OUT
ZONE 3
OUT VIDEO
VIDEO S-VIDEO FRONT CENTER
SUBWOOFER
SURROUND SURROUND BACK
FRONT CENTER
CENTER L R FRONT B L R SURROUND BACK/ L R SURROUND
SUBWOOFER
SURROUND SURROUND BACK
(Single)
(Single)
L
L
R
SEE INSTRUCTION
MANUAL
L
R
L
R
FM UNBAL 75 AM LOOP
SELECTABLE
VOIR LE MODE
D'EMPLOI
SELECTABLE
COAXIAL
ASSIGNABLE
IN 2 (CD)
ASSIGNABLE
(CD-R)
IN 4
ZONE3/
SOURCE
OUT
1 2
OPTICAL COAXIAL
DIGITAL OUT
OPTICAL
DIGITAL IN
SC-07
CD-R, MD, DAT, etc.
Note
1 • If your digital component only has a coaxial digital output, you can connect it to one of the coaxial inputs on this receiver using a coaxial
cable. When you set up the receiver you’ll need to tell the receiver which input you connected the component to (see also The Input Setup
menu on page 92).
• The digital outputs from other components can be connected to any spare digital audio inputs on this receiver. You can assign them when
setting up the receiver (see also
The Input Setup menu on page 92).
2 • When you want to record the source connected to ZONE3/SOURCE OUT, set ZONE3 to OFF. If you want to listen to the sound output from
ZONE3/SOURCE OUT in the sub zone without recording it, set ZONE3 to ON. See Using the MULTI-ZONE controls on page 68.
• In order to record some digital sources, you must make analog connections as explained in
Connecting analog audio sources on page 25.
3 • Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other
countries.
• With WMA9 Pro, sound problems may occur depending on your computer system. Note that WMA9 Pro 96 kHz sources will be
downsampled to 48 kHz.
SC07-05.book Page 24 Friday, April 25, 2008 11:59 AM