Pioneer Elite SC-07 - Manual (Page 99)

Using other functions 13
99
En
For more information about video connections, see
Connecting a DVD/HDD recorder, VCR and other video
sources on page 22.
1 Select the source you want to record.
Use the input source buttons (or INPUT SELECT).
• If necessary, set the operation selector switch to RCV,
then press SIGNAL SEL to select the input signal
corresponding to the source component (see
Choosing the input signal on page 38 for more on
this).
2 Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
3 Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording
device and set the recording levels.
Refer to the instructions that came with the recorder if
you are unsure how to do this. Most video recorders set
the audio recording level automatically—check the
component’s instruction manual if you’re unsure.
4 Start recording, then start playback of the source
component.
Reducing the level of an analog signal
The input attenuator lowers the input level of an analog
signal when it’s too strong. You can use this if you find
that the
OVER indicator lights often or you can hear
distortion in the sound.
1
• Set the operation selector switch to RCV, then press
A.ATT to switch the input attenuator on or off.
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
• Set the operation selector switch to RCV, then press
SLEEP repeatedly to set the sleep time.
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
cycle through the sleep options again.
2
Dimming the display
You can choose between four brightness levels for the
front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
• Set the operation selector switch to RCV, then press
DIMMER repeatedly to change the brightness of the
front panel display.
Note
1 The attenuator isn’t available with digital sources, or when using the Stream Direct (ANALOG DIRECT) modes.
DVD
MULTI
OPERATION
SOURCE TV RCV
VIDEO1
GALLERY
HOME MEDIA
INPUT SELECT
CD
HDMI
VOL
VOL CH
XM SIRIUS TUNER
PHONO
VIDEO2 VIDEO3 DVR2
BD TV DVR1
CD-R
DVD
VIDEO1
GALLERY
HOME MEDIA
INPUT SELECT
CD
HDMI XM SIRIUS TUNER
PHONO
VIDEO2 VIDEO3 TV
BD DVR1 DVR2
CD-R
SOURCE TV RCV
PARAMETER
TOP MENU
BAND
iPod CTRL
CATEGORY
EXIT TOOLS
HOME
MENU
STATUS
THX MPX MEMORY
PHASE CTRL CH LEVEL
MENU
T.EDIT
PARAMETER
PGM
STEREO/ A.L.C.
BD MENU
SIGNAL SEL SLEEP AUDIO DIMMER
SR+ SBch MCACC
AUTO/ DIRECT STANDARD ADV SURR
RETURN
TUNE
TUNE
ST ST ENTER
SIGNAL SEL
SOURCE TV RCV
VOL
VOL CH
SOURCE TV RCV
SIGNAL SEL SLEEP AUDIO DIMMER
SR+
CLR
SBch MCACC
A.ATT GENRE HDMI OUT
D.ACCESS
ENTER
CLASS
DISP
CH
A.ATT
2 You can also switch off the sleep timer simply by switching off the receiver.
SOURCE TV RCV
VOL
VOL CH
SOURCE TV RCV
PGM
STEREO/
A.L.C.
BD MENU
SIGNAL SEL SLEEP AUDIO DIMMER
SR+ SBch MCACC
A.ATT GENRE HDMI OUT
DISP
AUTO/
DIRECT STANDARD ADV SURR
SLEEP
30 min 60 min
90 min Off
SOURCE
TV RCV
VOL
VOL
TVCONTROL
CH
SOURCE
TV RCV
PGM
STEREO/ A.L.C.
BD MENU
SIGNAL SEL SLEEP AUDIO DIMMER
SR+ SBch MCACC
A.ATT GENRE HDMI OUT
DISP
AUTO/ DIRECT STANDARD ADV SURR
DIMMER
SC07-05.book Page 99 Friday, April 25, 2008 11:59 AM