Panasonic AJ-HD1400E - Manual (Page 53)

53
Setup menus
(continued)
DIF
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
“Menus which are displayed” (page 32).
“_____” indicates the factory setting.
No./Item Description of setting
880* 1
DIF SPEED
For setting the transfer speed of the IEEE1394 digital
interface output.
0000
S100 :
100 Mbps
0001 S200 :
200 Mbps
0002 S400 :
400 Mbps
<Note>
When S100 has been selected as this item’s setting,
DVCPRO HD format signals cannot be input or
output.
882* 1
DIF IN CH
For setting the input channel.
0000
0
: :
0063
63
The input channel is fixed at the channel
corresponding to the number specified.
0064 AUTO :
The input channel is not fixed at the channel
corresponding to the number specified. The input
channel is initialized to 63 when the power is
turned on.
883* 1
DIF OUT CH
For setting the output channel.
0000
0
: :
0063
63
The input channel is fixed at the channel
corresponding to the number specified.
0064 AUTO :
The output channel is not fixed at the channel
corresponding to the number specified. The output
channel is initialized to 63 when the power is
turned on.
886* 1
DIF CONFIG
Menu item for expansion purposes. Normally, use
DFLT as the setting.
0000
DFLT
0001 1
: :
0255
255
890* 1
DIF AUD OUT
For setting the audio channels to which the signals
from the IEEE1394 digital interface are to be output in
the DV format when a DVCPRO HD tape or 50M
format tape is played back or when a DV tape in 4ch
mode is played by the audio signals and menu No.
891 DIF DV AUDIO is set to “LOCK48.”
0000
CH1/2 :
CH1 and CH2
0001 CH3/4 :
CH3 and CH4
891* 1
DIF DV
AUDIO
For setting forcible audio mode conversion when a DV
tape is played back and the audio signals are output
in the DV format.
0000
THRU :
Normal setting (the signals simply pass through).
0001 LOCK :
Forcible conversion to the LOCK mode (no
frequency conversion)
0002 LOCK48 :
Forcible conversion to 48kHz/2CH/LOCK.
No./Item Description of setting
892* 1
DIF SIG CMD
For setting how to reply when signals requesting a
confirmation of the format is sent from an external
device connected by the IEEE1394 digital interface.
0000
50M :
DVDPRO50 is forcibly returned.
0001 25M :
DVDPRO is forcibly returned.
0002 DV :
DV is forcibly returned.
0003 AUTO :
The reply is the same format as the signal format
output from the IEEE1394 digital interface.
<Note>
When the unit is connected to a non-linear editing
system using 50M, 25M, and DV signal format, the
non-linear editing system may not operate properly. In
this case, set the value to reply with the format signal
supporting the connected signal format and start the
system.
894* 1
HD > DIF
OUT
For selecting channels that are adjusted with the
audio volume control on the front panel and displayed
on the audio level meter.
0000
HD :
DVCPRO HD
0001 50M :
DVCPRO50
0002 DV :
DV
895* 1
50M > DIF
OUT
For setting the format of the signals to be output from
the IEEE1394 digital interface when a 50M format
tape is played back.
0000
50M :
DVCPRO50
0001 DV :
DV
<Note>
When DV is selected as this item’s setting, the closed
caption signals and time code (VITC) signals in the
vertical blanking period are transmitted, but none of
the other signals in the vertical blanking period are
transmitted.
896*
1
25M > DIF
OUT
For setting the format of the signals to be output from
the IEEE1394 digital interface when a 25M format
tape is played back.
0000
25M :
DVCPRO
0001 DV :
DV
899* 1
DIF SUPER
For setting whether the superimposed display is to be
output from the IEEE1394 digital interface when the
format is converted (from HD to 50M, from HD to DV,
from 50M to DV or from 25M to DV).
0000
OFF :
The superimposed text is not displayed.
0001 ON :
The superimposed text is displayed.
<Note>
Only TCR is displayed.