Panasonic SC-BT203 - Manual (Page 26)

26
RQT9371
Listening to the Radio
Up to 30 stations can be set in each band, FM and AM.
1 Press [RADIO] to select “FM” or “AM”.
2 Press [STATUS] to select the position to start the
auto preset search.
Each time you press the button:
LOWEST (factory preset):
To begin auto preset with the lowest frequency.
(FM: 87.9 or 87.5, AM: 520)
CURRENT:
To begin auto preset with the current frequency.*
* To change the frequency, refer to “Manual tuning”. (B right)
3 Press and hold [OK].
Release the button when “AUTO” is
displayed.
The tuner starts to preset all the stations it
can receive into the channels in ascending
order.
≥“SET OK” is displayed when the stations are set, and the radio tunes
to the last preset station.
≥“ERROR” is displayed when automatic presetting is unsuccessful.
Preset the stations manually. (B right)
1 Press [RADIO] to select “FM” or “AM”.
2 Press the numbered buttons to select the
channel.
To select a 1-digit number
e.g., 1: [1] > [OK].
To select a 2-digit number
e.g., 12: [1] B [2]
Alternatively, press [W, X] or [2, 1].
When a stereo FM broadcast is being received,
“ST” lights in the display.
≥The FM/AM setting is also shown on the TV display.
∫ If noise is excessive
When FM is selected
Press [AUDIO] to display “MONO”.
Press the button again to cancel the
mode.
≥The mode is also canceled when you change the frequency.
≥This setting can be preset for each broadcasting station. When
“MONO” appears, follow procedures 1 and 2 in “Presetting stations
manually”. (> below)
When AM is selected
Press [AUDIO] to select “AM BP1” or “AM BP2” (whichever
receives the better quality).
Each time you press the button:
AM BP1
(.AM BP2 (BP=Beat Proof)
1 Press [RADIO] to select “FM” or “AM”.
2 Press [SEARCH
6] or [SEARCH5] to select
the frequency.
≥Main unit:
Press [X TUNE W] to select the frequency.
≥When a radio broadcast is being
received, “T” lights in the display.
≥To start automatic tuning, press
and hold [SEARCH6] or
[SEARCH5] (main unit: [X TUNE W]) until the frequency
starts scrolling.
Tuning stops when a station is found.
∫ Presetting stations manually
Up to 30 stations can be set in each band, FM and AM.
1 While listening to the radio broadcast
Press [OK].
2 While “P” is flashing on the display
Press the numbered buttons to select a channel.
To select a 1-digit number
e.g., 1: [1] > [OK].
To select a 2-digit number
e.g., 12: [1] B [2]
A station previously stored is overwritten when another station is
stored in the same channel preset.
FM frequency step
Main unit:
The factory setting is set to 0.2 MHz, it can be changed to receive broadcasts allocated in 0.1 MHz. You may need to change this setting
if the tuner seems to skip over the correct frequency for stations in your area.
1 Press [SELECTOR] to select “FM”.
2 Press and hold [SELECTOR].
After a few seconds the display changes to show the current lowest frequency. Continue to hold the button down. The lowest frequency changes
and the step is changed.
To return to the original settings, repeat steps 1 and 2.
Setting up the radio
Presetting stations automatically
1
@.
2 3
4 5 6
7 8
0 9
OK
EXT-IN
RADIO
STATUS AUDIO
ABC DEF
JKL MNO
TUV
GHI
QRS
P
XYZ
W
_,
SEARCH SEARCH
Numbered
buttons
RADIO
AUDIO STATUS
,
SEARCH
SEARCH
OK
TUNE SELECTOR SETUP MIC SD CARD TUNE SELECTOR
SELECTOR TUNE
Listening/confirming the preset
channels
Manual tuning
ST
T MONO
T MONO
After changing the setting, previously preset frequencies will be cleared. Preset them again.
NOTE
Radio
BT300.book 26 ページ ２００９年３月１２日 木曜日 午後６時３４分