Panasonic SC-BT203 - Manual (Page 45)

45
RQT9371
Wireless connections (optional)
∫ Wireless setup diagram
e.g., 7.1ch
LS: Surround (left), RS: Surround (right)
≥Place on the side of the seating position, about 1 m (3 ft) higher than
ear level.
LB: Surround back (left), RB: Surround back (right)
≥Place behind the seating position, about 1 m (3 ft) higher than ear level.
∫ Digital transmitter
Remove the digital transmitter cover before installing any
optional digital transmitter.
≥Replace the cover when the digital transmitter is not in use.
∫ Wireless system
Preparation
If the surround/surround back speaker cables (with a blue connector,
with a gray connector, with a brown connector and a tan connector)
have already been connected, disconnect them from the main unit and
the speakers and connect the cables supplied with the wireless
system to the speakers.
Connecting the cables
Connect to terminals of the same color.
≥It is also possible to use the original cables supplied with the main
unit.
– Connect the underlined color cables when using the main unit's cables.
Left side speakers
SURROUND (LS): Blue (Blue)
SURROUND BACK (LB): Gray (Brown)
Right side speakers
SURROUND (RS): Gray (Gray)
SURROUND BACK (RB): Blue (Tan)
Connecting the speakers to the wireless system
Setting the Surround selector
∫ AC power supply cord
Connecting the speakers with the optional wireless system (SH-FX70: 2 units)
≥Turn off all equipment before connection and read the
appropriate operating instructions.
≥Connect the AC power supply cord after all other
connections are complete.
≥Do not use the wireless system and digital transmitter in a
metal cabinet or bookshelf.
≥Place the wireless system within approximately 15 m
(47 ft) from the home theater unit.
Connections
Do not insert or remove while the main unit is on.
LS
LB RB
RS
Main unit
(with the digital
transmitter)
Seating position
Wireless system Wireless system
Surround speaker cables
NOTE
ANT EXT LOOP AM
GND ANT LOOP
TRANSMITTER
DIGITAL
ANT EXT LOOP AM
GND ANT LOOP
TRANSMITTER
DIGITAL
TRANSMITTER
DIGITAL PUSH PUSH
PUSH PUSH
TRANSMITTER
DIGITAL PUSH PUSH
SH-TR70 digital transmitter
Insert fully until you hear a click.
Digital transmitter cover
You can use the blunt end of a writing instrument to
push here until the cover pops out.
Main unit Main unit
SPEAKERS
ENCEINTES
LS / RB LB / RS
SURR I/D SET
AC IN
SURROUND (3 – 6 )
AMBIOPHONIQUES L SIDE R SIDE
Speaker cable
Insert fully.
Making the wireless link
1 Turn on the wireless system.
2 Turn on the main unit.
The wireless link indicator on the main unit will be turned on.
3 Turn on the additional wireless system.
4 While pressing [5/9] on the main unit, press the
numbered button [3] on the remote control until “P” lights in
the main unit’s display.
5 While “P” is displayed, press
[I/D SET] on the rear of the
additional wireless system.
≥The indicator on the additional
system turns green.
≥If “P” goes off before you press
[I/D SET], repeat step 4 and
then continue the procedure.
6 While pressing [5/9] on the main unit, press the
numbered button [3] on the remote control.
7 Turn off and on the additional wireless system.
≥Make sure the indicator on the additional wireless system lights
up green.
8 Start play on the main unit.
≥For optimal audio output, it is recommended to re-configure
the main unit using SMART SETUP / EASY SETUP.
(> 15)
≥If you should change the digital transmitter, repeat the
pairing steps for both units of the wireless system, one unit
at a time.
≥You cannot use the wireless system with SH-FX65T or
SH-FX67T digital transmitter.
SPEAKERS
ENCEINTES
LS / RB LB / RS
SURR I/D SET
AC IN
SURROUND (3 – 6 )
AMBIOPHONIQUES L SIDE R SIDE
SURR
L
SIDE
R
SIDE
L
SIDE
R
SIDE
Selector setting for the left speakers
Selector setting for the right speakers
AC power supply cord
(included with SH-FX70)
To household AC outlet
(AC 120 V, 60 Hz)
WIRELESS LINK POWER
Wireless unit on/off button [POWER C I, B Í]
Use this button to turn the unit on and off.
C I: The unit is on.
B Í: The unit is off.
WIRELESS LINK indicator
Red: The unit is on and the wireless link is deactivated.
Green: The unit is on and the wireless link is activated.
SLP STCT
RDS RND PGM
EQ
PRG SRDE.
PL DDTS
W2 WS W1
≥If the indicator is flashing, refer to the
“Optional wireless system (SH-FX70)” in
the Troubleshooting guide. (> 49)
e.g.

Use a pointed object.
NOTE
Optional speaker
settings
BT300.book 45 ページ ２００９年３月１２日 木曜日 午後６時３４分