Power-on recording, Manual recording, Alarm recording – Panasonic WJ-HD220 User Manual
Page 51: Time&date search rec stop rec, Alarm 1 alarm 1 duration alarm 2 alarm 2 duration, Sensor built-in vmd, Timer switch ac mains
51
Orange: The channel image is not displayed.
Yellow: The channel image is displayed.
The multiscreen monitor displays the recording images
while the corresponding input indicators on the front
panel light in yellow.
2. Hold down the [REC STOP] button for 2 seconds to
stop recording. The REC indicator turns off.
■ Alarm Recording
Alarm recording starts when an externally connected sen-
sor is turned on, the built-in VMD (Video Motion Detector) or
the built-in video loss detection is activated.
Alarm recording will proceed, then stop when the post-
recording time has elapsed.
If more than one alarm arise, for instance ALM1 and ALM2,
the images of the alarmed inputs are recorded on the disk
as shown in the figure.
Note: HDD indicator will continue to blink for a period
equivalent to the specified pre-alarm time at the end of
alarm recording.
■ Power-on Recording
For power-on recording, select EXT for TIMER in the WJ-
HD220 MAIN menu. The recorder starts recording when AC
power is supplied.
This enables the disk recorder to start recording everyday
at a specific time by the use of a timer switcher that con-
trols the AC mains supplied to the recorder. The power
switch on the rear of the recorder must be turned on in this
case.
■ Manual Recording
Manual recording is available when OFF is set for TIMER in
the WJ-HD220 MAIN menu. The menu setup can exempt
specific inputs from manual recording for the purpose of
preserving disk capacity. The recording mode (SF-24, for
example), picture quality (fine) and recording rate (30 fps)
are set in the menu setup by specifying two of the three
parameters. SF-24H is an example having a picture quality
of especially fine grade and 48 hours of recording capacity.
1. Press the [REC] button on the front panel to start
recording. The indicator in the [REC] button lights up
while the [CAM SEL] button of the channel indicates
and the channel image is displayed on the multiscreen
monitor.
Sensor
Built-in
VMD
OPERATE
ALARM
SUSPEND
RESET
HDD
FULL
ERROR
OSD
MULTISCREEN
SELECT
ZOOM
TIMER
REMOTE
LOCK
SEQUENCE
ALARM
SERCH
STOP
PLAY MODE SELECT
SETUP
/ESC
PLAY
TIME&DATE
SEARCH
REC STOP
SPOT
MULTI
CAMERA SELECT
ALARM
RECALL
REC
PUSH— PAUSE SET
Digital Disk Recorder WJ-HD220
1
5
2
6
3
7
4
8
DST
C
4
C
8
C
1
C
1
C
1
C
1
C
1
C
2
C
1
C
2
C
2
C
2
C
2
C
2
C
3
C
4
C
8
Alarm 1
Alarm 1 Duration
Alarm 2
Alarm 2 Duration
C
1
C
2
C
3
C
4
C
8
C
1
C
2
C
3
C
4
C
8
C
1
C
2
C
3
C
4
C
8
C
1
C
2
C1
C2
C3
C4
C5
C6
C7
C8
C1
Start
Stop
TIME&DATE
SEARCH
REC STOP
REC
Timer
Switch
AC Mains
OPERATE
ALARM
SUSPEND
RESET
HDD
FULL
ERROR
OSD
MULTISCREEN
SELECT
ZOOM
TIMER
DST
REMOTE
LOCK
SEQUENCE
ALARM
SERCH
STOP
PLAY MODE SELECT
SETUP
/ESC
PLAY
TIME&DATE
SEARCH
REC STOP
SPOT
MULTI
CAMERA SELECT
ALARM
RECALL
REC
PUSH— PAUSE SET
Digital Disk Recorder WJ-HD220
1
5
2
6
3
7
4
8