Panasonic NV-DV2000EC - Manual (Page 49)

Programme Editing
49
To continue setting programmes:
1 Press EDIT MENU.
2 Press PLAYER.
3 Using 21 (CURSOR), select the programme
number.
The programme number changes each time
these buttons are pressed.
Up to 10 programmes can be set.
4 Repeat steps 4–9.
10 Press 34 (CURSOR)
to select Preview to
confirm the editing
operation before
performing actual
editing, and then press
OK.
≥
Preview begins after the playback unit and the
recording VCR both rewind their tapes to the edit
start points.
11 Press 34 (CURSOR)
to select Start Insert to
start editing, and then
press OK.
≥
Editing begins after
the playback unit and
the recording VCR
both rewind their
tapes to the edit start
points.
12 After completing editing,
press 34 (CURSOR)
to select Review, and
then press OK.
≥
The edited pictures
are played back.
To interrupt editing, Preview or Review:
Press EDIT MENU.
Review
1
V i d e o I n s e r t
1 PLAYER RECORDER ¥
Insert in Progress
1
Video Insert
Confirm/Change
Insert a programme
Erase a programme
Preview
Start Insert
Review
Timing Adjust
Video Insert
Confirm/Change
Insert a programme
Erase a programme
Preview
Start Insert
Review
Timing Adjust
Notes:
≥
Programme Editing can be performed using either the
tape counter or Time code display.
≥ If you attempt to switch to the tape counter display in
order to perform editing after setting the editing points
using the Time code display, the Erase all
programmes screen is displayed.
(The Erase all programmes screen is also displayed
when you change from the tape counter display to the
Time code display.)
≥ After setting a programme, if you attempt to set
another programme in a different editing mode, the
set contents for the previous editing mode remain on
the setting screen. In order to prevent editing errors,
perform the Erase all programmes operation [
R53]
whenever you set a programme under a different
editing mode.
≥ Programme Editing can not be performed with a video
movie camera that has a 4-digit counter.
≥ Video Insert and Audio Insert are not possible in
the following cases:
When the tape in the recording VCR (the NV-DV2000)
is:
Recorded in LP mode;
Blank, or contains a blank portion in the middle.
≥ AV Insert is not possible in the following cases:
When the tape in the recording VCR (the NV-DV2000)
is:
Recorded in 16bit audio mode;
Recorded in LP mode;
Blank, or contains a blank portion in the middle.
When INPUT SELECT is set to DV1 or DV2.
Notes on editing point setting
≥
The Programme Insert and Audio Dubbing functions
require the setting of only three editing points: the in
and out points on the playback unit and the in point
on the recording unit, or the in point on the playback
unit and the in and out points on the recording unit.
≥ If both in and out points are set on both the playback
unit and the recording unit, and the times between the
points do not match, editing stops at the first out point
that is reached.
≥ In order to ensure that the editing operation is
performed properly, the editing points should be set at
least 20 seconds after the beginning of the tape.
≥ The editing operation may not be performed correctly
if the set duration of a programme is less than
4 seconds.
≥ On a video equipment whose Time code display or
tape counter display does not show the frame value,
the area where the frame value is displayed appears
as “00f” or it remains blank.
With some units, the frame value may be displayed
when MARK IN or MARK OUT is pressed in steps
5 and 6 even if the unit concerned does not show the
frame value.
≥ Up to n1 second of slight deviation in the specified
edit start/end position can be corrected. See [
R54]
for Edit Timing Adjustment.