Panasonic AJ-HD1700PE - Manual (Page 101)

101
Setup menus
The underlining (__) denotes the factory setting mode.
<AUDIO> (continued)
No./Item Description of setting No./Item Description of setting
739
CH2 CUE SEL
For selecting the CH2 output status of the
main signal line in the search mode.
0000 OFF:
The CUE signal is not output.
0001 ON:
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to “Audio
outputs in the search mode” on page 103.
740
CH3 CUE SEL
For selecting the CH3 output status of the
main signal line in the search mode.
0000 OFF:
The CUE signal is not output.
0001 ON:
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to “Audio
outputs in the search mode” on page 103.
745
CH8 CUE SEL
For selecting the CH8 output status of the
main signal line in the search mode.
0000 OFF:
The CUE signal is not output.
0001 ON:
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to “Audio
outputs in the search mode” on page 103.
741
CH4 CUE SEL
For selecting the CH4 output status of the
main signal line in the search mode.
0000 OFF:
The CUE signal is not output.
0001 ON:
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to “Audio
outputs in the search mode” on page 103.
742
CH5 CUE SEL
For selecting the CH5 output status of the
main signal line in the search mode.
0000 OFF:
The CUE signal is not output.
0001 ON:
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to “Audio
outputs in the search mode” on page 103.
743
CH6 CUE SEL
For selecting the CH6 output status of the
main signal line in the search mode.
0000 OFF:
The CUE signal is not output.
0001 ON:
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to “Audio
outputs in the search mode” on page 103.
746
MONI CH SEL
For selecting the monitor output.
0000 MANU:
The signal selected by the MONITOR SELECT
button is output.
0001 AUTO:
The PCM audio signal is output in the j 1.0 k
to i 2.0 k speed range; the CUE signal is
automatically output at all other speeds.
0002 PCM:
The PCM audio signal is output in the j 32 k to
i 32 k speed range.
<Notes>
• When “AUTO” is selected and a tape in any format
except DVCPRO HD-LP is played back, the PCM
audio signals are output in the -1.0
k to +1.1 k speed
range.
• This setting takes effect when the L and R MONITOR
SELECT switches on the VTR’s front panel have
selected a channel from CH1 to CH8.
(If they have selected CUE, the CUE signal is output
at all speeds regardless of this menu item’s setting.)
747
MON AUTO
SEL
For selecting the channel for the monitor
output to be switched to CUE.
When a setting other than “MANU” has been
selected for setup menu item No.746 (MONI CH
SEL), the CUE signal is automatically output to
the monitor output in accordance with the
operation mode, and the monitor channel to be
switched to CUE is selected automatically.
0000 L/R: The CUE signal is output both
to the Lch and Rch.
0001 L: The CUE signal is output to the
Lch only
.
0002 R: The CUE signal is output to the
Rch only.
744
CH7 CUE SEL
For selecting the CH7 output status of the
main signal line in the search mode.
0000 OFF:
The CUE signal is not output.
0001 ON:
The CUE signal is output.
<Note>
For details on the audio output statuses, refer to “Audio
outputs in the search mode” on page 103.
748
MONI SEL INH
For selecting whether to enable or inhibit the
operation of the MONITOR SELECT button on
the front panel.
0000 OFF: The button’s operation is
enabled.
0001 ON: The button’s operation is
inhibited.
0002 ON1: In the FULL display mode,
operation is prohibited; in the
FINE
display mode only,
operation is enabled.
<Note>
Whether to enable or inhibit the button’s operation can
be selected for channels whose signals have not been
mixed by the setup menu item No.737 (MONI MIX)
setting.