Panasonic AJ- E - Manual (Page 41)

4
Chapter 4 Adjustments and settings for recording
41
Display item What is displayed Status when display appears
This appears when the position of the WHITE BAL switch has been
changed. “A,” “B” or “PRE” appears at #. VAR ¢.¢ K is displayed
when channel A, Y is set to VAR. ATW MODE is displayed when ATW
is assigned to channel B.
This appears when the AUTO KNEE switch has been set to ON or OFF.
This appears when the gain has been selected using the GAIN selector
switch or USER button.
This indicates the shutter speed value when the shutter speed has been
selected.
This appears when synchro scan has been selected as the shutter
speed.
This appears when SUPER V has been selected as the shutter speed.
This appears when the filter setting has been selected.
This appears when the lens extender has been set to ON or OFF.
This appears when the iris overwrite correction value has been changed. (Switch selection
displays) WHITE: # ¢.¢K
AUTO KNEE: ON/OFF
GAIN: ¢¢dB
SS: 1/¢¢¢¢
SS: 1 1/¢¢¢¢
SS: SUPER V
FILTER: ¢ ¢.¢K
EXTENDER: ON/OFF
IRIS: ¢¢ F ¢ ¢
This appears when the brightness has dropped. (LOW LIGHT
warning display) LOW LIGHT
With the Y GET ON setting, the output brightness level near the center
marker is displayed as “%.” (Y GET value) ¢¢¢ .¢%
This indicates the type of marker presently being displayed. (MARKER display) MKR: A/B/OFF
This appears during an ABB operation.
This appears when the ABB operation has been completed satisfactorily.
This appears when the ABB operation has been forcibly terminated.
This appears when the ABB operation has not been completed satisfactorily.
This appears during a WHITE SHADING operation.
This appears when the WHITE SHADING operation has been
completed satisfactorily.
This appears when the WHITE SHADING operation has been forcibly
terminated.
This indicates that white shading has not been completed satisfactorily
as the brightness level was excessively high during the WHITE
SHADING operation.
This appears when the BLACK SHADING operation is ready to be
performed as a result of holding down the ABB switch for a length of
time during an ABB operation.
This appears during a BLACK SHADING operation.
This appears when the BLACK SHADING operation has been
completed satisfactorily.
This appears when the BLACK SHADING operation has been forcibly
terminated.
This appears when the BLACK SHADING operation has been not
completed satisfactorily.
This warns the user that the brightness is too high during the BLACK
SHADING operation. 3 Camera warning
and message
display area
(Displays related to
the AWB, ABB and
switch operations) ABB ACTIVE
ABB OK
ABB BREAK
ABB NG
W-SHD ACTIVE
W-SHD OK
W-SHD BREAK
W-SHD NG
LVL OVER
B-SHD READY
B-SHD ACTIVE
B-SHD OK
B-SHD BREAK
B-SHD NG
B-SHD LVL OVER
4 Information
allocated to USER
buttons
UM: USER MAIN
U1: USER1 button
U2: USER2 button
INH
S.GAIN ¢¢dB/OFF
DS.GAIN ¢¢
:/OFF
S.IRIS ON/OFF
I.OVR ON/OFF
S.BLK –¢¢/OFF
B.STR ON/OFF
AUDIO CH1
AUDIO CH2
“INH” is indicated when the operation of the USER button has been disabled.
This indicates the value selected for S.GAIN.
This indicates the value selected for DS.GAIN.
This indicates whether S.IRIS is set to ON or OFF.
This appears when the IRIS OVERRIDE setting is enabled (ON).
This indicates whether SUPER BLACK is set to ON or OFF and, if it is
set to ON, it also indicates its value.
This indicates whether BLACK STRETCH (black level gradation
compensation) is set to ON or OFF.
This appears when the input signal to recorded on audio channel 1 has
been switched.
This appears when the input signal to recorded on audio channel 2 has
been switched.
This appears when the call command has been issued from the extender. (CALL display) CALL