Pelco Universal Keyboard KBD300A - Manual (Page 29)

Pelco Manual C527M-L (3/04) [ 29 ]
Table D. Keyboard Functions (continued)
Function Procedure
Auxiliaries/ For the CM6700:
Relays F1 – F3
ᕥ
control only the auxiliaries built into the CM6700 SCU.
These outputs can be programmed for momentary, keyed, latched, or alarm op-
eration. Refer to the CM6700 manual for programming instructions.
F1/LATCH: Activate/deactivate auxiliary 1 relay.*
F2/OFF:
Activate/deactivate switcher auxiliary 2 TTL output.*
F3/MOM: Activate/deactivate switcher auxiliary 3 TTL output.*
The AUX ON and AUX OFF keys
ᕦ
control the auxiliaries in receivers.
Enter the auxiliary number and press the AUX ON key to turn on. Hold, and
then release for momentary functions.
Enter the auxiliary number and press the AUX OFF key to turn off.
For the CM6800:
F1-F3
ᕥ
can address auxiliary functions on the CM6800 and on the REL2064
(a separate auxiliary relay box) to provide additional auxiliary points.
F1/LATCH: Enter the auxiliary number and press and release F1 to turn on an
auxiliary (latching).
F2/OFF: Enter the auxiliary number and press and release F2 to turn off an
auxiliary (latching).
F3/MOM: Enter the auxiliary number and press and hold down F3 to turn on
an auxiliary (momentary). Release F3 to turn off the auxiliary.
Direct Mode:
In Direct Mode, F1- F3
ᕥ
have no function. LED
ᕡ
shows receiver auxiliary
number for two seconds after the AUX ON or AUX OFF key
ᕦ
is pressed.
Acknowledge Press ACK
ᕫᕺ
to acknowledge an alarm (or to halt pattern programming).
Alarm* Refer to the CM6700 or CM6800 manual for further information on alarms.
Program For the CM6700:
(CM6700) To program the CM6700 switcher, press PGM
ᕧ
.
(CM6800) Follow the programming procedure in the CM6700 manual. LED display
ᕡ
shows P in program mode. To exit, navigate to the RETURN field and press ACK
ᕫᕺ
or tap the joystick
ᕫᕵ
to the right and release.
For the CM6800:
To program the CM6800 switcher, press PGM
ᕧ
.
Follow the programming procedure in the CM6800 manual. To exit, navigate to
the RETURN field and tap the joystick
ᕫᕵ
to the right and release. Or, press the
PGM key
ᕧ
to return to the previous screen or menu.
LED LED
ᕡ
shows monitor number (in CM6700 and CM6800 modes) or camera/
receiver number (in Direct Mode) and P (in Program Mode).
Firmware Version LED
ᕡ
flashes for a few seconds to show firmware version on power up (not
functional on versions prior to 4.0).
Clear Press CLEAR
ᕫᕷ
to cancel a number that has been entered. (CM6700/
CM6800 modes only.) In Direct Mode, this key erases any numerical entries
entered and redisplays the current camera number selected.
Infrared Filter This function applies to Spectra ® color/black-white model SD5BCBW only.
(IR Cut Filter) a. To turn on the filter; press 8, 8, PRESET
ᕩ.
b. To turn off the filter, press 8, 9, PRESET
ᕩ.
Shift* Press SHIFT
ᕢ to allow the keyboard to send multiplexer commands.
*This function is not used in Direct Mode.
9