Caution – Tanita Body Composition Analyzer BC-418MA User Manual
Page 15
GB
GB
Output (Fat Monitor Mode) Format
a Transmission Data
a Control Commands
Remote Mode
All types of data may be entered by connecting the BF-350 to a PC and switching to Remote mode.
When in Remote mode, the body fat analyzer may be operated remotely by sending control commands from a host.
a Error Codes
If an error occurs, the body composition analyzer will send an error code to the host.
a Switching to Remote Mode
The receiving PC must be ready to accept output data immediately after
measurement is completed.
ƽ
CAUTION
Output data
Byte Length
First byte
1
1
5
Second byte
K: unit of weight kg
L: unit of weight lb
S: stability of load (weight output)
D: instability of load (weight output)
I : overload status
---: negative weight output
Header
Weight
xxx.x
Output data format
¥ Terminal data are CR (ASCII format: 0DH), LF (ASCII format: 0AH).
¥ Measurement data will be sent in the format shown to the right:
x x x x x . x
1. When the unit is switched off, press the [
]
and [
] keys simultaneously.
ƽ
Note
The default setting is off.
2. Press [0], [8].
3. Switch Remote mode on and off by pressing [1]
or [0].
[1] : Enables Remote mode
[0] : Disables Remote mode
4. Press [
] to confirm.
Only "r S" will appear (standby screen).
ƽ
Note
To switch off Remote mode, start
from the beginning again and
select "OFF" at Step 3.
ATHLETIC
STEP ON
FEMALE
MALE
kg
cm / ft.in
STABILIZED
AGE
% FAT
P T
ATHLETIC
STEP ON
FEMALE
MALE
kg
cm / ft.in
STABILIZED
AGE
% FAT
P T
ATHLETIC
STEP ON
FEMALE
MALE
kg
cm / ft.in
STABILIZED
AGE
% FAT
P T
ATHLETIC
STEP ON
FEMALE
MALE
kg
cm / ft.in
STABILIZED
AGE
% FAT
P T
*All fixed-length data right aligned. Enter
for blanks.
0
U? : Confirm current setting
U0: Use cm/kg mode
U1: Use in/lb mode
LF
CR
1
U
LF
CR
0
U
LF
CR
?
U
commands
U
R? : Confirm current setting
R0: Select equation for Westerners
R1: Select equation for Orientals
LF
CR
1
R
LF
CR
0
R
LF
CR
?
R
commands
R
D? : Confirm current setting
D0 : Set clothing weight (5-byte fixed length)
D1 : Set gender male = 1 female = 2
D2 : Set body type standard = 0 athlete = 2
D3 : Set height (5-byte fixed length)
D4 : Set age (2-byte fixed length)
D6 : Set Target BF (2-byte fixed length)
LF
CR
X
X
6
D
LF
CR
X
X
4
D
LF
CR
X
X
X
X
X
3
D
LF
CR
X
2
D
LF
CR
X
1
D
LF
CR
X
.
X
X
X
0
D
LF
CR
?
D
commands
D
G1: Start measuring body fat
G2: Measure weight only
LF
CR
2
G
LF
CR
1
G
commands
G
CHR$(01FH): Reset settings
LF
CR
CHR$(01FH)
Special
commands
E00 : Attempted to start measuring without completing settings
E01 : Error in calculating body fat percentage
EXX :other error ’ body fat analyzer switches off
LF
CR
X
X
E
LF
CR
1
0
E
LF
CR
0
0
E
*See p.26 "7. Troubleshooting" for details of errors.