Yamaha RX-V1000RDS - Manual (Page 72)

70
SOUND FIELD PROGRAM PARAMETER EDITING
Changing Parameter Settings
You can enjoy good quality sound with the factory-set
parameters. Although you do not have to change the
initial settings, you can change some of the parameters to
better suit the input source or your listening room.
Adjustments should be made with the remote control.
y
• We recommended that you edit the parameter while using a
video monitor. It is easier to see the video monitor than it is to
see the front panel display.
1 Set PARAMETER/SET
MENU to PARAMETER.
2 Turn on the video monitor
and press ON SCREEN
repeatedly to select the
full display mode.
Program No. Program name (group)
Cursor
Parameters
Example of ROCK CONCERT
4 Press k / n to select the
parameter.
5 Press –/+ to change the
parameter value.
y
• When you set the parameter to a value other than the factory-
set value, an asterisk mark (*) appears by the parameter name
on the video monitor.
6 Repeat steps 3 to 5 above as necessary to
change other program parameters.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
Resetting a Parameter to the
Factory-set Value
■ To reset some of the parameters
to the factory-set values
Select the parameter you want to reset. Then press and
hold – or + until the value temporarily stops at the
factory-set value. The asterisk mark (*) by the parameter
name disappears on the video monitor.
■ To reset all of the parameters to
the factory-set values
Use “9 PARAM. INI” on the SET MENU to reset all of
the parameter values of all DSP programs within the
selected group to the factory-set values (see page 45).
This operation resets all of the parameter values of all
DSP programs within that group to the factory-set values.
Notes
• The available parameters may be displayed on more than one
OSD page for some of the programs. To scroll through pages,
press k / n.
• You cannot change parameter values when “15 MEMORY
GUARD” on the SET MENU is set to ON. If you want to
change the parameter values, set “15 MEMORY GUARD” to
OFF (see page 47).
PARAMETER
SET MENU
ON SCREEN
10KEY DSP HALL 1 HALL 2 CHURCH JAZZ CLUB
ROCK
CONCERT STADIUM
TV
SPORTS
ENTER-
TAINMENT
6.1/ES
MONO
MOVIE MOVIE
THEATER 2
MOVIE
THEATER 1
/DTS
SUR.
0 +10 +100
1 2 3 4
5 6 7 8
9 10 11 12
+ + +
TV VOL
A / B / C / D / E PRESET
TV INPUT
TV MUTE
CH
DISC
MUTE
EFFECT
VOLUME
CHP/INDEX
– – –
ON SCREEN LEVEL
SLEEP TEST
PARAMETER
SET MENU
3
2
4
5
1
P05 ROCK CONCERT
INIT.DLY 15ms
5
7%
REV.TIME
LIVENESS
REV.DELAY
REV.LEVEL 100ms
1.6s
3 Select a DSP program you want to adjust.
HALL 1 HALL 2 CHURCH JAZZ CLUB
ROCK
CONCERT STADIUM
TV
SPORTS
ENTER-
TAINMENT
MONO
MOVIE MOVIE
THEATER 2
MOVIE
THEATER 1
/DTS
SUR.
0 +10 +100
1 2 3 4
5 6 7 8
9 10 11 12
10KEY DSP
0112V1000RDS_69-74_EN 9/5/0, 4:44 PM 70