Petzl AVAO BOD FAST - Manual (Page 5)

5
C71 AVAO BOD - AVAO BOD FAST
C715010C (060213)
EN
Only the techniques shown in the diagrams that are not crossed out, and that do not
display a skull and crossbones symbol and/or «NO!» are authorized. Some examples
of misuse are presented, but it is impossible to describe them all. Check www.petzl.
com regularly to find the latest technical information.
Contact Petzl if you have any doubt or difficulty understanding these documents.
1. Field of application
Personal protective equipment (PPE).
Fall arrest body harness, work positioning and restraint belt and seat harness for
work at height.
This product must not be loaded beyond its strength rating, nor be used for any
purpose other than that for which it is designed.
WARNING
Activities involving the use of this equipment are inherently dangerous.
You are responsible for your own actions and decisions.
Before using this equipment, you must:
- Read and understand all instructions for use.
- Get specific training in its proper use.
- Become acquainted with its capabilities and limitations.
- Understand and accept the risks involved.
Failure to heed any of these warnings may result in severe injury or
death.
Responsibility
WARNING, specific training is essential before use. This training must be adapted to
the practices defined in the Field of Application.
This product must only be used by competent and responsible persons, or those
placed under the direct and visual control of a competent and responsible person.
Gaining an adequate apprenticeship in appropriate techniques and methods of
protection is your own responsibility.
You personally assume all risks and responsibilities for all damage, injury or death
which may occur during or following incorrect use of our products in any manner
whatsoever. If you are not able, or not in a position to assume this responsibility or to
take this risk, do not use this equipment.
2. Nomenclature of parts
- Chest harness:
(1) Dorsal attachment point, (2) Rear dorsal point adjustment buckle, (3) Front sternal
point adjustment buckles, (4) Sternal attachment point, (5) Chest-seat harness
connector, (6) Elastic retainers, (7) Velcro retainer for arranging a lanyard, (8) Tool
holder loops.
- Seat harness:
(9) Textile attachment point for chest-seat harness connector, (10) Waistbelt straps,
(11) Leg loop straps, (12) Ventral attachment point, (13) Waistbelt side attachment
points, (14) Rear restraint attachment point, (15) DoubleBack adjustment buckles for
leg loops, (15 bis) FAST rapid buckles for leg loops, (16) Equipment loops, (17) Tool
holder loops, (18) Plastic retainers, (19) Leg loop retainers, (20) Leg loop-chest
harness linking strap, (21) DoubleBack waistbelt adjustment buckles, (22) CARITOOL
slots.
Principal materials:
Straps: polyester, nylon.
Adjustment buckles: steel.
Attachment points and front chest-seat harness connector: aluminum alloy.
3. Inspection, points to verify
Before each use
Harness
Check the webbing at the attachment points, at the adjustment buckles and at the
safety stitching.
Look for cuts in the webbing, wear and damage due to use, to heat, and to contact
with chemical products, etc.. Be particularly careful to check for cut threads.
Verify that the DoubleBack and FAST buckles operate properly.
Chest-seat harness connector
Make sure the frame, gate, hinge and locking sleeve are free of any cracks,
deformation, corrosion, etc.. Open the gate and verify that it closes and locks
correctly. The Keylock slot must not be blocked by any foreign matter (dirt,
pebble, etc.).
Consult the details of the inspection procedure to be carried out for each item of PPE
on the Web at www.petzl.com/ppe.
Contact Petzl if you have any doubt.
During each use
It is important to regularly monitor the condition of the product and its connections
to the other equipment in the system. Make sure that all pieces of equipment in the
system are correctly positioned with respect to each other.
4. Compatibility
Verify that this product is compatible with the other elements of the system in your
application (compatible = good functional interaction).
5. How to put the harness on
- Be sure to correctly stow the excess webbing (folded flat) in the retainers.
Be careful of foreign bodies which can impede the operation of the FAST buckles
(such as pebbles, sand, clothing...). Verify that the buckles are correctly fastened.
Chest-seat harness connector:
Do not use it to attach a lanyard or energy absorber.
ATTENTION DANGER, it must always be used with the gate closed and locked. Its
strength is greatly reduced if the gate is open.
Systematically verify the gate is closed by pressing it with your hand. Contaminants
such as mud, sand, paint, ice, dirty water, etc. can prevent the locking system from
working.
Initial adjustment of the dorsal attachment point:
This adjustment should be done only once when putting on your harness for the first
time. Have another person help you do it.
Adjust the position of the dorsal attachment point to suit your body shape and
size: position it at the level of the shoulder blades.
Adjustment and suspension test
Your harness must be adjusted to fit snugly to reduce the risk of injury in case of a
fall.
You must move around and hang in the harness from each attachment point, with
your equipment, to verify that the harness fits properly, provides adequate comfort for
the intended use and that it is optimally adjusted.
6. Fall arrest harness EN 361: 2002
Body harness for fall arrest, component of a fall arrest system in accordance with the
EN 363 standard (personal fall arrest systems). It must be used in conjunction with
EN 795 anchors, EN 362 locking carabiners, EN 355 energy absorber, etc..
6A. Sternal attachment point
6B. Dorsal attachment point
Only these points may be used to attach a fall arrest system, for example a mobile fall
arrester, an energy absorber, or other system described in the EN 363 standard. For
ease of identification, these points are marked with the letter ‘A’.
Clearance: amount of free space below the user
The clearance below the user must be sufficient to prevent the user from striking
any obstacle in case of a fall. Specific details on calculating clearance are found
in the technical notices for the other components (energy absorbers, mobile fall
arrester, etc.).
7. EN 358: 1999 harness for work
positioning and restraint
These attachment points are designed to either hold the user in position at the work
station, or to prevent the worker from entering a zone where a fall is possible. These
attachment points must only be used to attach to a restraint or work positioning
system, maximum fall height: 0.5 m.
These attachment points are not designed for fall arrest usage. It may be necessary
to supplement work positioning or travel restraint systems with collective or personal
fall arrest systems.
7A. Ventral attachment point
7B. Waistbelt side attachment points
Always use the two side attachment points together by linking them with a
positioning lanyard in order to be comfortably supported by the waistbelt.
7C. Rear restraint attachment point
This rear waistbelt attachment is designed only for attachment of a restraint system
to prevent the user from entering an area where a fall is possible.
Regularly check the effectiveness of the system during use (adjustment and
attachment elements).
8. Seat harness:
EN 813: 2008
Ventral attachment point
Nominal maximum load: 140 kg.
Designed for progression on rope and work positioning.
Use this ventral ring to attach a descender, positioning lanyards or progression
lanyards.
This attachment point should not be used to attach fall arrest systems.
9. Equipment loops
The equipment loops must only be used to attach and support equipment.
WARNING DANGER, never use equipment loops for belaying, rappelling, tying-in, or
anchoring a person.
10. Supplementary information regarding
standards EN 365
Rescue plan
You must have a rescue plan and the means to rapidly implement it in case of
difficulties encountered while using this equipment.
Anchors
The anchor point for the system should preferably be located above the user’s
position and should meet the requirements of the EN 795 standard (minimum
strength of 10 kN).
Various
- In a fall-arrest system, it is essential to check the required clearance under the user
before each use, to avoid any impact with the ground or an obstacle in case of a fall.
- Make sure that the anchor point is correctly positioned, in order to limit the risk and
the height of a fall.
- A fall arrest harness is the only device allowable for supporting the body in a fall
arrest system.
- When using multiple pieces of equipment together, a dangerous situation can result
if the safety function of one piece of equipment is affected by the safety function of
another piece of equipment.
- WARNING DANGER, take care that your products do not rub against abrasive or
sharp surfaces.
- Users must be medically fit for activities at height. Warning, inert suspension in a
harness can result in serious injury or death.
- The instructions for use for each item of equipment used in conjunction with this
product must be respected.
- The instructions for use must be provided to users of this equipment in the
language of the country in which the product is to be used.
11. Petzl general information
Lifetime / When to retire your equipment
For Petzl’s plastic and textile products, the maximum lifetime is 10 years from the
date of manufacture. It is indefinite for metallic products.
WARNING: an exceptional event can lead you to retire a product after only one use,
depending on the type and intensity of usage and the environment of usage (harsh
environments, marine environment, sharp edges, extreme temperatures, chemical
products, etc.).
A product must be retired when:
- It is over 10 years old and made of plastic or textiles.
- It has been subjected to a major fall (or load).
- It fails to pass inspection. You have any doubt as to its reliability.
- You do not know its full usage history.
- When it becomes obsolete due to changes in legislation, standards, technique or
incompatibility with other equipment, etc..
Destroy retired equipment to prevent further use.
Product inspection
In addition to the inspection before each use, an in-depth inspection must be carried
out by a competent inspector. The frequency of the in-depth inspection must be
governed by applicable legislation, and the type and the intensity of use. Petzl
recommends an inspection at least once every 12 months.
To help maintain product traceability, do not remove any markings or labels.
Inspection results should be recorded on a form with the following details: type of
equipment, model, manufacturer contact information, serial number or individual
number, date of manufacture, date of purchase, date of first use, date of next
periodic inspection, problems, comments, the name and signature of the inspector.
See an example at www.petzl.com/ppe.
Storage, transport
Store the product in a dry place away from exposure to UV, chemicals, extreme
temperatures, etc.. Clean and dry the product if necessary.
Modifications, repairs
Modifications and repairs outside of Petzl facilities are prohibited (except replacement
parts).
3-year guarantee
Against all material or manufacturing defect. Exclusions: normal wear and tear,
oxidation, modifications or alterations, incorrect storage, poor maintenance,
negligence, uses for which this product is not designed.
Responsibility
Petzl is not responsible for the consequences, direct, indirect or accidental, or any
other type of damage befalling or resulting from the use of its products.
Traceability and markings
a. Body controlling the manufacture of this PPE
b. Notified body that carried out the CE type inspection
c. Traceability: datamatrix = product reference + individual number
d. Diameter
e. Individual number
f. Year of manufacture
g. Day of manufacture
h. Control or name of inspector
i. Incrementation
j. Standards
k. Read the Instructions for use carefully