Q-Tech CLASS B+ - Manual (Page 13)

Q-TECH Corporation - 10150 W. Jefferson Boulevard, Culver City 90232 - Tel: 310-836-7900 - Fax: 310-836-2157 - www.q-tech.com
13 of 27
Q-TECH
CORPORATION
QPDS-0001, Rev L, June 2013 (ECO #10851)
CLASS B+ PRODUCTS
HIGH RELIABILITY HYBRID CRYSTAL CLOCK OSCILLATORS
2.5 to 5.0Vdc - 15kHz to 350MHz
Electrical Parameter Test Conditions
Limits
Notes
Min. Nom. Max. Units
Frequency Range +3.3Vdc or +5.0Vdc
.015 85 MHz TO, DIP, FP20
0.450 85 MHz Other Packages
Frequency/Temperature Stability See temperature codes -55 +25 +125 °C (See Note 1)
Supply Voltage
3.0
4.5
3.3
5.0
3.63
5.5
Vdc
Vdc
Input Current at 3.63Vdc
Measured without load
at maximum Vdd
3
6
10
20
30
mA
15k-<500kHz
500k-<16MHz
16M-<32MHz
32M-<60MHz
60M-70MHz
Input Current at 5.5Vdc
Measured without load
at maximum Vdd
20
25
35
45
mA
15k-<16MHz
16M-<32MHz
32M-<60MHz
60M-85MHz
Output Voltage VOL
Vdd x 0.1
Vdc
0.4 (TTL)
Output Voltage VOH
Vdd x 0.9
Vdc
2.4 (TTL)
Output Waveform Square Wave N/A
Rise and Fall Time
10% to 90%
(0.8V to 2.0V for TTL)
6
3
ns
ns
15k-<30MHz
30M-85MHz
Duty Cycle
50% of output
(1.4Vdc for TTL)
45
40
50 55
60
%
%
15k-<16MHz
16M-85MHz
Load
15pF//10kΩ (CMOS)
6TTL to 10TTL (TTL)
Per MIL-PRF-55310 loads
Frequency Aging after 30 days 70°C±3°C ±1.5 ppm (See Note 2)
Frequency Aging/Year 70°C±3°C ±5 ppm (See Note 3)
Start-up Time 100µs ramp 10 ms
Output Enable VIH 2.2 Vdc
Output Disable VIL 0.8 Vdc Output High Impedance
Frequency Voltage Tolerance
over ±10% change
in supply voltage
-2 +2
ppm
TO, DIP, FP
-4 +4 All Ceramic Packages
Electrical Performance Characteristics 15kHz to 85MHz
(For FACT +5Vdc and +3.3Vdc CMOS Outputs Using 54ACT3301NSC)
NOTES:
1. Frequency stability compared to nominal frequency including initial accuracy at 25°C, load, and supply variations ±10%.
2 Normally frequency aging is up 30 days. However, aging may be ceased if value at 15 days is half than the limit of 30-day aging
value, or continued up to 90 days if value exeeds 30 day aging limit.
3. Aging is ±5ppm after first year and ±2ppm/year thereafter.
Parameters Symbol Min. Max. Units
Supply Voltage Vdd -0.5 +7 V
Operating Temperature Top. -55 +125 °C
Storage Temperature Tstg -62 +125 °C
Lead Solder Temperature 260/10 °C/seconds
Package Thermal Resistance ѲJc 50 °C/W
Junction Temperature +175 ºC
Maximum Ratings
Recommended Operating Conditions