Extron Electronics MAV Plus series Large Scale Setup Guide - Manual (Page 15)

Cr
ossPoint / MA
V Matrix Switchers • Remote Contr
ol
Remote Contr
ol, cont’d
4-4
Cr
ossPoint / MA
V Matrix Switchers • Remote Contr
ol
4-5
Refer also to the
Cr
ossPoint 450 Plus / MA
V Plus User’
s Manual
at
www
.extron.com
.
Refer also to the
Cr
ossPoint 450 Plus / MA
V Plus User’
s Manual
at
www
.extron.com
.
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Create ties
N • Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*24$.
• The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
N When you create a tie where X! = 00, you tie no input to the specified output ( X@ ) (untie X@ ).
When you create a tie where X@ = 00, you untie all outputs from input X! .
N The & tie command for RGB and the % tie command for video can be used interchangeably.
N The & read tie command for RGB and the % read tie command for video can be used interchangeably.
Tie input X! to output X@ , video
and audio
X! * X@ ! Out X@ • In X! • All ] Tie input X! ‘s video and audio to output X@ .
Example: 1*3! Out03•In01•All ] Tie input 1 video and audio to output 3.
Tie input X! to output X@ , RGBHV X! * X@ & Out X@ • In X! • RGB ] Tie RGB only (video breakaway).
Example
(see 3rd Note, above): 10*4& Out04•In10•RGB ] Tie input 10 RGB to output 4.
Tie input X! to output X@ , video X! * X@ % Out X@ • In X! • Vid ] Tie video only (video breakaway).
Example
(see 3rd Note, above) 7*5% Out05•In07•Vid ] Tie input 7 video to output 5.
Tie input X! to output X@ , audio X! * X@ $ Out X@ • In X! • Aud ] Tie audio only (audio breakaway).
Example: 24*04$ Out04•In24•Aud ] Tie input 24 audio to output 4.
Read RGB output tie X@ & X!] RGBHV input X! is tied to output X@ .
Read video output tie X@ % X!] Video input X! is tied to output X@ .
Read audio output tie X@ $ X!] Audio input X! is tied to output X@ .
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Video and audio mute commands
RGB/video mute X@ *1B Vmt X@ *1 ] Mute output X@ RGB (video off).
RGB/video unmute X@ *0B Vmt X@ *0 ] Unmute output X@ RGB (video on).
Read RGB/video mute X@ B X#] 1 = mute on, 0 = mute off.
Global RGB/video mute 1*B Vmt1 ] Mute all RGB outputs.
Global RGB/video unmute 0*B Vmt0 ] Unmute all RGB outputs.
Audio mute X@ *1Z Amt X@ *1 ] Mute output X@ audio (audio off).
Audio unmute X@ *0Z Amt X@ *0 ] Unmute output X@ audio (audio on).
Read audio mute X@ Z X#] 1 = mute on, 0 = mute off.
Global audio mute 1*Z Amt1 ] Mute all audio outputs.
Global audio unmute 0*Z Amt0 ] Unmute all audio outputs.
View output mutes E VM } X$ 1 , X$ 2 , ... X$ n ] Each X$ response is the mute status of an output,
starting from output 1.
n
= the maximum number of outputs for this model.
Example:
CrossPoint 450 Plus 6432 HVA
E VM } Mut02202000000000000000000000000000 ]
Output 2, 3, and 5 audio is muted. All other
outputs are unmuted.
N The “Mut” portion of the response appears only when the switcher is in Verbose mode 3. See the Verbose mode command on page 4-.
N
X!
= Input number 00 – (maximum number of inputs for your model) (00 = untie)
X@ = Output number 00 – (maximum number of outputs for your model) (00 = untie all outputs)
N
X@ = Output number 01 – (maximum number of outputs for your model)
X#
= Mute 0 = off (unmuted)
1 = on (muted)
X$ = Video/audio mute: 0 = no mutes
1 = video mute
2 = audio mute