Anemostat EST - Manual (Page 3)

3
1220 Watson Center Road • Carson, CA 90745
Tel: (310) 835-7500 • Fax: (310) 835-0448
www.anemostat.com • [email protected]
Model QST Number Description
Digit 1, 2, 3 - Model
QST Series flow fan powered terminal
Digit 4 - Heat options
S Standard
W Hot water coil
E Electric heat
Digit 5, 6, 7, 8 - Fan Horsepower and Primary inlet size
1706 1/6 hp 6” inlet
1707
1/6 hp 7” inlet
1708 1/6 hp 8” inlet
2508 1/4 hp 8” inlet
2509 1/4 hp 9” inlet
2510 1/4 hp 10” inlet
5010 1/2 hp 10” inlet
5012 1/2 hp 12” inlet
5014 1/2 hp 14” inlet
7512 3/4 hp 12” inlet
7514 3/4 hp 14” inlet
1012 1 hp 12” inlet
1014 1 hp 14” inlet
1016 1 hp 16” inlet
Digit 9 - Casing Construction
B single wall 20ga. Steel (standard)
E double wall 22ga. Steel
(1/2” glass fiber insulation)
F low temp casing
(1” matte faced glass fiber insulation)
Digit 10 - Insulation and Treatment
0 None
1
1/2” matte-faced glass fiber insulation
(double wall only)
2 1” matte-faced glass fiber insulation (standard)
(also req’d for low temp casing)
3 1/2” foil-faced glass fiber
(tape over all insulation edges)
4 1” foil-faced glass fiber
(tape covers insulation edges)
5 3/8” closed cell insulation (fiber free)
Digit 11 - Control Type
0 None
P
Pneumatic
A Electronic Analog
F Supplied by others – factory mounted
Digits 12, 13, 14, 15 - Control Package
0000 None (field supplied by others)
XXXX Refer to pages 365 and 366
Digit 16 - Control location
(determined by facing inlet)
L left hand
Digits 17, 18, 19, 20 - Primary air minimum airflow
0000 None specified
XXXX Specify minimum airflow setting in CFM
Refer to pages 365 and 366 for allowable range
Digits 21, 22, 23, 24 - Primary air maximum airflow
0000 None specified
XXXX Specify maximum primary airflow setting
in CFM. Refer to pages 365 and 366
Digit 25 - Heating coil and connection location (determine
by facing inlet)
0 None
A
One-row hot water coil - right hand
B One-row hot water coil - left hand
C Two-row hot water coil - right hand
D Two-row hot water coil - left hand
K Electric heat - connections same side
as digit 16
Digit 26 - Fan Motor Voltage
1 115V/ 1 Ph./ 60 Hz.
2 277V/ 1 Ph./ 60 Hz.
Note: Standard motor is 3 speed multi-tap PSC
Digit 27 - Electric Coil Voltage and Steps
0 None
A
208V/ 1 Ph/ 60Hz. 1 step
B 208V/ 1 Ph/ 60Hz. 2 step
C 208V/ 1 Ph/ 60Hz. 3 step
D 240V/ 1 Ph/ 60Hz. 1 step
E 240V/ 1 Ph/ 60Hz. 2 step
F 240V/ 1 Ph/ 60Hz. 3 step
G 277V/ 1 Ph/ 60Hz. 1 step
H 277V/ 1 Ph/ 60Hz. 2 step
J 277V/ 1 Ph/ 60Hz. 3 step
K 208V/ 3 Ph/ 60Hz. 1 step
L 208V/ 3 Ph/ 60Hz. 2 step
M 208V/ 3 Ph/ 60Hz 3 step
N 480V/ 3 Ph/ 60Hz. 1 step
P 480V/ 3 Ph/ 60Hz. 2 step
R 480V/ 3 Ph/ 60Hz. 3 step
Note: 3 steps not available with night setback control packages
Digits 28, 29, 30 - Electric coil KW
000 None
XXX Refer to notes on pages 369 and 370 for
allowable range
Digit 31 and over - Options and Accessories
C1 Unit mounting brackets
C2 Manual damper locking quadrant (shipped loose)
C4 Hinged front panel control enclosure
C5 Discharge collar (“S” units only)
D3 Line voltage SPST disconnect switch
(120V, 277V)
D5 Line voltage power-fusing
(fuse and block for 120V, 277V)
D7 Three speed motor switch
(terminal selector block standard)
D8 Fan Relay, 24 VAC Coil, SPST / N.O.
(for DDC controls by others)
D9 24 VAC Electric Actuator
DA 24 VAC Transformer, 40 VA
E1 Non-fused interlocking disconnect switch
for Electric heat
E2 Electric heat Mercury de-energizing
contactors
E3 Electric heat power fusing
(fuses and fuse blocks)
E4 Electric heat manual reset secondary
thermal cutout
E6 AirFlow proving switch
F1 One inch throwaway filters
Standard Digits 1-3 4 5,6 7,8 9 10 11 12-15 16 17-20 21-24 25 26 27 28-30 31-32 33-34 35-+
Description Model Heat HP Inlet Casing Insul Cntrl Cntrl LH Min Max Heat Fan Coil Elec Opt Opt Opt
Num Type Pkg CFM CFM Config VAC VAC KW
Example QST W 25 10 B 1 A 5001 L 0100 1450 E 1 G 12 C1 C4 F1
Must be 4 wire
WYE configuration