Contemporary Research ICC1-IR IR - Manual (Page 16)

Contemporary Research 16 ICC1-IR
RS-232 Commands
Ts & Qs The ICC1-IR responds to Q-series tuning commands as well
Channel Up TU “$A5,<dh>,<dl>,2,’TU’ ” (6 bytes) – Tunes to next channel up in Tune Ring
Channel Dwn TD “$A5,<dh>,<dl>,2,’TD’ ” (6 bytes) – Tunes to next channel down in Tune Ring
TU and TD control analog channels stored in the TR command – designed for legacy
Smart TV installs, not contemporary HDTV applications
T Channel Prev TP “$A5,<dh>,<dl>,2,’TP’ ” (6 bytes) – Tunes to previous channel in Tune Ring
Force Channel
TC “$A5,<dh>,<dl>,3,’TC’, <channel>” (7 bytes) – Tunes to a specific channel
Select Channel TT “$A5,<dh>,<dl>,2,’QT’,<channel>” (7 bytes) – Tunes channel if included in TR
Tune Ring
TR “$A5,<dh>,<dl>,<ncb>,’TR’, [<chan 1>, <chan N>]” (variable bytes)
This command stores a Tune Ring, Analog channels only , a series of preset
channels accessed by channel up/down commands.
Ex1: “$A5,<dh>,<dl>,6,’TR’, 5,4,8,11” sets ring to channels 5, 4, 8 and 11
Tip: The ring follows the stored order, channels do not have to be in ascending
order
Ex2: “$A5,<dh>,<dl>,8,’TR’, $82,5,$87,11” sets channels 2-5 and 7-11. You can
specify a range using MSB bit for the first channel; the next byte is the last.
Control Lock LM “$A5,<dh>,<dl>,3,'LM',<control>” (7 bytes)
Locks power operation – only functional with display with power current sensor.
When the control is locked, the display is locked to the power state of the ICC1-IR.
For example, if the ICC1-IR power state is off, the display can’t be turned on from
the IR remote or TV front panel. The controller will sense the change from the
power sensor and turn the set off.
0 = Unlock, 128 = Lock
Tuning Style H1= “$A5,<dh>,<dl>,3,’H1’,<style>” (7 bytes)
1 = 5-digit CableCard style tuning (1-9999)
2 = Virtual HD Major-Minor tuning (tunes to virtual channel ID in display)
3 = Physical HD Major-Minor tuning (physical channel, minor digital)
TC Response H2= “$A5,<dh>,<dl>,3,’H2’,<response>” (7 bytes)
This pre-sets how the ICC1-IR will respond to TC tuning commands.
0= Ignore, use current settings
1= Analog Only (XX-0)
2= Digital (XX-1)
Tune HD TH
Ex:
“$A5,<dh>,<dl>,5,’TH’,<H1>,<Major>,<Minor>” (9 bytes) – Digital Tuning
Normally, the H1 parameter is 0, allowing the ICC1-232 to use the current H1 tuning
format, but it could be used to force a different tuning option. When the display is
set to the H1=1 mode, 1-part digital channel, the first byte is (x*256), and the last
byte is the value you add to state the channel number. In H1=2 or 3 modes, the
bytes represent the Major and Minor channel numbers.
This command is designed for compatibility with other ICC controllers. In reality, H1
modes 2 and 3 are the same for IR control.
“$A5,1,4,5,’TH’,1,2,3” Device 260, channel 515
“$A5,1,4,5,’TH’,2,2,3” Device 260, virtual channel 2-3
“$A5,1,4,5,’TH’,3,2,3” Device 260, physical channel 2, minor 3