LEDGlow Million Color SMD LED Underbody Lighting Kit with Bluetooth Connectivity - Manual (Page 3)

10. Find a safe, secure, and dry place to mount the underbody tube
junction box. We recommend mounting the junction box inside the car, if
possible. If this is not possible, we suggest mounting the junction box in
you engine bay in the driest location available. Improper installation or
water damage to the control box or kit will void all warranties.
Optional: For extra protection, apply a thin bead of silicone along the
seams of the control box, distributor cable, and connections to seal them.
11. Mount the underbody kit’s control box in a safe and secure location
inside of your vehicle. Connect the underbody tube junction box’s
distributor cable to the control box. If the junction box is mounted inside of
your engine bay, run the lead wire through a pre-existing hole with a
grommet in your firewall and to the control box. If you do not have a pre-
existing hole in the firewall you can drill one, just be sure to use a rubber
grommet to ensure the lead wire is not cut or pinched.
This underbody kit can be powered one of two ways:
1. Connect the red power wire to any 12 volt source. If
you need to extend the power wires, be sure to only use 14 or 16 gauge
automotive grade wire. If you are running the power wire to the battery, it
must go through the firewall by using an existing grommet or by drilling a
hole and adding a new grommet, which is available at any auto parts store.
Be sure to install a fuse within 6 inches of the power source. (You will have
to install an additional fuse if you have to extend the wires.) Do not run
the wire through the door jam. The wire can be pinched and will void all
warranties.
2. This underbody kit can also be powered directly from
your vehicle’s fuse box. If you are powering the kit via the fuse box,
LEDGlow recommends that you install the wire using LEDGlow’s Expandable
Circuit, which is available on LEDUnderbody.com.
Note: The controller has a built-in power save mode, which is enabled
after 8 hours of inactivity with your device. This mode is designed to
prevent unnecessary battery drain. If you would like to completely
remove power from the controller when not in use, connect the power
wires to a 12V switched source.
12. Connect the black wire to a unpainted bare metal ground source. A couple of good ground sources are under the dash at any main bracket or grounding
block, the negative post on your battery, or any engine ground.
13. Beginning with the rear tube, run the power wire to the location of the junction box. Make sure to secure the wires tightly when going around the suspension
parts and/or exhaust. Leave at least 8 inches between the exhaust and the underbody tube. If a power wire is pinched, the kit may malfunction and the
warranty will be voided. Run the rear tube’s power wire along one of the side tubes and make sure it is tightly secured. Next, run both side tubes power
wires to the junction box. Finally, run the front tube’s power wire to the junction box.
14. It is imperative to make sure that the wires are not mounted to any direct heat source or to any moving parts. Any excess length on the tube power wire will
have to be bound up and secured tightly.
15. DO NOT SHORTEN OR CUT ANY OF THE UNDERBODY TUBE POWER WIRES. This will destroy the kit and void all warranties.
16. Lower the vehicle if it was raised, power on and test the underbody kit for full functionality, not only using the buttons on the control box, but also with the
LEDGlow Mobile Control App using your iOS or Android device.
17. Once the vehicle is on the ground, turn the steering wheel as far as it can go in both directions to ensure the tubes and/or wires are not coming in contact
with your tires or any other moving parts. If a tube or wire is damaged by the tire and/or any moving parts the warranty will be voided.
Optional Interior Add On Tube Installation:
1. Once your underbody kit is installed you can start installing your optional interior lighting tubes.
2. Connect the interior tube junction box, the box with 6 ports, to the port on the control box that is labeled “Light 2”
3. Depending on which kit your purchased will determine tube placement, but you can install these interior tubes anywhere you would like. We recommend
either under your dashboard, under your front seats, under the rear seats, or even in your trunk.
Warning: The interior tubes are only intended to be installed to the interior of your vehicle, and are not water resistant. Mounting these tubes outside of
the vehicle could cause water damage, and will void LEDGlow’s warranty.
Warning: Do not shorten or cut the lead power wires on the interior tubes, this will destroy the kit and void the warranty.
4. Once you have determined the mounting location for your interior tubes, clean any dirt, oil, dust, or cleaning product from the surface using an alcohol prep
pad.
5. Using the included 3M tape and screws mount the interior tube clips to your mounting location and snap the interior tubes into the clips. If you are unable to
mount the tubes to a flat location using the clips, mount the tubes using the included zip ties.
6. Once you are done mounting all of your interior tubes, run the lead power wire from each tube to the interior tube junction box. Be sure to keep the lead
wires away from any moving parts, for example, the pedals, steering column, and/or seat tracks.