Alpine PXA-H800 - Manual (Page 32)

30
-EN
01GB06PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From a PC
Setting the 2-Channel Signal Playback
Mode (2ch Playback Mode)
These steps set the 2-channel signal playback mode.
1
Click [Multi Channel Manager] of the Function
switching tab.
Multi Channel Manager tab screen will be displayed.
• Refer to “Operating the Function Switching Tab” (page 7).
2
Set and adjust “2ch Playback Mode,” “EUPHONY,”
“Dolby Pro Logic II.”
• When both Rear and Center speakers are off in “Setting the Speaker
System (Output System Select)” (page 13)/ “Setting the Speakers
(Speaker Setup)/Setting the Subwoofers” (page 14), this item cannot
be set.
• After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 12).
When playing back 2-Channel Stereo, select a playback mode best
suited to the music. (Initial setting: “Stereo”)
1
Click [ ] for “2ch Playback Mode” and select and
click the playback mode you want from the pull-
down menu.
Setting contents: Stereo/Rear Fill/EUPHONY/Dolby Pro
Logic II
Stereo: Plays back in 2ch stereo.
Rear Fill: Outputs the front signal from the rear.
EUPHONY: Plays back in 5.1 channel surround
(page 30).
Dolby Pro Logic II: Plays back in Dolby Pro Logic II
surround (page 31).
• For linear PCM, the front signals are sent to the rear channel even if
the system is set up for “Stereo.”
• “Rear Fill” function
Depending on the input signals, the sound may only be output from
the front speakers. In this case, the “Rear Fill” function can be used
to output signals from the rear speakers as well.
• If the setting of Rear Fill is made when Rear Mix is ON, sound is
unchanged in the rear fill setting because Rear Mix is given priority
during 2 channel decoder other than linear PCM.
EUPHONY creates 5.1 channel surround using Adaptive Surround
technology based on a music signal recorded in 2-channel.
When you set up EUPHONY and play back a CD or iPod stereo source,
you can enjoy the realistic sensation of musicians playing around you.
For DVD movie playback, you can enjoy the sense of localization of the
dialogue and impressive three-dimensional sound effects.
In this setting, EUPHONY Mode can be selected. (Initial setting:
“ACOUSTIC”)
1
Click [ ] for “2ch Playback Mode” and select and
click [EUPHONY] from the pull-down menu.
• If you click [EUPHONY] for [shortcut] tab in the main menu, the
Multi Channel Manager tab screen can also be displayed and you
can set up EUPHONY.
2
Click [ ] for “EUPHONY” and select and click the
mode from the pull-down menu.
• This function only works with 2-channel signals.
Use the Multi
Channel Function
Setting the 2-Channel Signal Playback
Mode (2ch Playback Mode)
Setting EUPHONY (EUPHONY)
Setting contents: ACOUSTIC/LIVE/CINEMA/TV SHOW/
Custom 1/Custom 2/Custom 3
ACOUSTIC: Localization is emphasized; the
mode with regular sound field
resonance.
LIVE: Ambience is emphasized; the mode
in which sound field resonance is
more strongly felt.
CINEMA: Mode suitable for movie audio.
Dialogues are reproduced clearly
and sound effect is crisp.
TV SHOW: Mode suitable for broadcasting
audio such as the digital
broadcasting.
Custom 1/Custom 2/
Custom 3: These can be selected only when
EUPHONY is customized in
“Customizing EUPHONY” (page 31).
01GB00PXAH800.book Page 30 Tuesday, February 8, 2011 9:04 PM