Alpine PXA-H800 - Manual (Page 54)

52
-EN
01GB07PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From the Commander
Setting the 2-Channel Signal Playback
Mode (Mode)
When playing back 2-Channel Stereo, select a playback mode best
suited to the music. (Initial setting: “Stereo”)
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Playback
Mode,” and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “Mode,” and
then press the [Rotary encoder].
The Mode selection screen is displayed.
4
Select the playback mode you want by rotating the
[Rotary encoder], and press the [Rotary encoder].
Setting contents: Stereo/Rear Fill/EUPHONY/Dolby PLII
Stereo: Plays back in 2ch stereo.
Rear Fill: Outputs the front signal from the rear.
EUPHONY: Plays back in 5.1 channel surround (page 52).
Dolby PLII: Plays back in Dolby Pro Logic II surround
(page 53).
5
When the setting is complete, press and hold [ ]
for at least 2 seconds.
• If [ ] is pressed during setting, the unit returns to the previous
item.
• For linear PCM, the front signals are sent to the rear channel even if
the system is set up for “Stereo.”
• “Rear Fill” function
Depending on the input signals, the sound may only be output from
the front speakers. In this case, the “Rear Fill” function can be used
to output signals from the rear speakers as well.
• If the setting of Rear Fill is made when Rear Mix is ON, sound is
unchanged in the rear fill setting because Rear Mix is given priority
during 2 channel decoder other than linear PCM.
• When both Rear and Center speakers are off in “Setting the Speaker
System (System Select)” (page 37)/“Setting the Speakers (Speaker
Setup)” (page 38), this item cannot be set.
• After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 36).
Setting EUPHONY (EUPHONY)
EUPHONY creates 5.1 channel surround using Adaptive Surround
technology based on a music signal recorded in 2-channel.
When you set up EUPHONY and play back a CD or iPod stereo source,
you can enjoy the realistic sensation of musicians playing around you.
For DVD movie playback, you can enjoy the sense of localization of the
dialogue and impressive three-dimensional sound effects.
In this setting, EUPHONY Mode can be selected. (Initial setting:
“ACOUSTIC”)
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Playback
Mode,” and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “Mode,” and
then press the [Rotary encoder].
The Mode selection screen is displayed.
4
Rotate the [Rotary encoder] to select “EUPHONY,”
and then press the [Rotary encoder].
5
Press [ ].
This will take you back to the Step 3 screen.
6
Rotate the [Rotary encoder] to select “EUPHONY,”
and then press the [Rotary encoder].
7
Rotate the [Rotary encoder] to select the mode, and
then press the [Rotary encoder].
Setting contents: ACOUSTIC/LIVE/CINEMA/TV SHOW/
Custom 1/Custom 2/Custom 3
ACOUSTIC: Localization is emphasized; the mode with
regular sound field resonance.
LIVE: Ambience is emphasized; the mode in which
sound field resonance is more strongly felt.
CINEMA: Sound suitable for movie audio. Dialogues are
reproduced clearly and sound effect is crisp.
TV SHOW: Sound suitable for broadcasting audio such as
the digital broadcasting.
• Custom 1/Custom 2/Custom 3 can be selected only when the feature
is set on a PC (see “Customizing EUPHONY” page 31).
Use the Multi
Channel Function
FUNC.
Rotary encoder
CHANNEL
01GB00PXAH800.book Page 52 Tuesday, February 8, 2011 9:04 PM