Alpine PXA-H800 User Manual
Page 53
51
-EN
01GB07PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From the Commander
• When you switch from “L or R” to “L+R,” choose which adjustment
of the R and L channels to be applied.
1 Select either “L
R” or “R
L” by rotating the [Rotary
encoder], and press the [Rotary encoder].
L
R: The adjustment of the L channel is to be applied to
both R and L channels.
R
L: The adjustment of the R channel is to be applied to
both R and L channels.
9
Select the channel you want to adjust by pressing
[CHANNEL].
L+R selected:
FRONT HIGH
FRONT MID
FRONT LOW
REAR
CENTER
SUBWOOFER*
1
FRONT HIGH
L or R selected: FRONT L HIGH
FRONT R HIGH
FRONT L MID
FRONT R MID
FRONT L LOW
FRONT R LOW
REAR L
REAR R
CENTER
SUBWOOFER*
2
FRONT L HIGH
*
1
If the Subwoofer output is set for Monaural, you can set both
SUBWOOFER 1 and 2.
*
2
If the Subwoofer output is set for Monaural, you can set
SUBWOOFER 1 and 2. If the Subwoofer output is set for Stereo, you
can set SUBWOOFER L and R.
• Channels to be set vary depending on the system set in “Setting the
Speaker System (System Select)” (page 37).
10
Adjust the calculated time correction value (0.00 to
20.00 ms) by rotating the [Rotary encoder].
Setting contents: 0.00 to 20.00 ms (in 0.05 ms steps)
• The distances can be displayed in either “cm” or “inch” (see
“Setting the Time Correction Adjustment Unit (TCR Parameter)”
page 51).
11
To adjust another channel, repeat Steps 9 through
10.
• You can listen with Defeat OFF (adjusted setup values) or with
Defeat ON (Initial value) to compare, by following the steps below.
1 Press and hold the [Rotary Encoder] for at least 2
seconds while in the adjustment mode.
2 Rotate the [Rotary Encoder] to switch on/off Defeat, and
listen to compare.
3 To exit, select “OFF” and then press [
].
• You can mute the channel you are adjusting.
1 Press [MUTE] while in the adjustment mode to mute the
channel.
2 To cancel muting, press [MUTE] again.
12
When the setting is complete, press and hold [
]
for at least 2 seconds.
• If [
] is pressed during setting, the unit returns to the previous
item.
• This function is not available when Defeat is set to ON.
• When the speaker is set to the “OFF” mode, the time correction for
that speaker cannot be set. Refer to “Setting the Speaker System
(System Select)” (page 37)/“Setting the Speakers (Speaker Setup)”
(page 38).
• After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 36).
Setting the Time Correction Adjustment
Unit (TCR Parameter)
The unit of measurement for time correction can be set as either “cm” or
“inch.” (Initial setting: “cm”)
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Sound Field
Adj.,” and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “Setup,” and
then press the [Rotary encoder].
4
Rotate the [Rotary encoder] to select “TCR
Parameter,” and then press the [Rotary encoder].
5
Select either “cm” or “inch” by rotating the [Rotary
encoder], and press the [Rotary encoder].
cm: The unit for the time correction becomes “cm.”
inch: The unit for the time correction becomes “inch.”
6
When the setting is complete, press and hold [
]
for at least 2 seconds.
• If [
] is pressed during setting, the unit returns to the previous
item.
Displaying the distances from the listening
positions to the speakers
01GB00PXAH800.book Page 51 Tuesday, February 8, 2011 9:04 PM