ProMariner Combi Inverter Charger - Manual (Page 5)

Tr u e P o w e r C o m b i F e a t u r e s
Overview
UNPACKING AND INSPECTION
Thoroughly inspect your TruePower Combi unit. Take care in moving the unit as it weighs
approximately 42 lbs.
The package should contain the following:
1) TruePower Combi unit
2) Parts package including:
a. +(Red) & -(Black) DC terminal covers and 8 (4 per cover) machine screws.
b. AC Terminal Cover and 2 strain relief connectors plus 2 screws
c. Remote package including panel, cable and mounting screws (if so equipped)
d. Owners/Installation manual
DAMAGE - If any parts are missing or damaged, or the unit has been damaged in shipping
contact ProMariner customer service at 1-800-824-0524, do not take back to place of
purchase.
DO NOT attempt to install or operate the unit if it has been damaged in any way.
T r u e P o w e r
O v e r v i e w
5
6
Features
SMART TECHNOLOGY - Your new ProMariner TruePower Combi unit is current limiting
with built in “smart” features to monitor vital functions and preclude damage to the
charger and the installed system. The unit incorporates alarms, indicators and an auto
shut-down feature for peace of mind and trouble free operation. This section contains
descriptions of the LED indications and functions of controls. A more detailed description
of LED and audible warning signals can be found in the Troubleshooting section. Turning
the unit OFF and ON again will restart the unit after a fault, however, if the fault is still
present, the unit will again shut down.
INVERTER – The TruePower Combi serves as a Pure Sine wave or a Quasi (modified) Sine
wave inverter, converting DC power to clean, reliable AC power.
NOTE: This unit requires a large amperage draw from a DC battery when in Inverter mode.
Care must be taken during installation to provide properly sized cables from the battery
to the inverter. Cable runs must be as short as possible and of the appropriate size and
type. See the Installation section for more details.
CHARGER – The TruePower Combi also serves as a high efficiency automatic battery charger
suitable for all commonly available battery types (See Section 3 on the Features Table) .
TRANFER SWITCH – The TruePower Combi includes an internal, automatic 30 amp AC
Transfer switch that senses the presence of AC shore/station power. Upon connection
to a shore power/shore station source, the Combi will switch from INVERTER mode
(providing AC power via DC battery source) to CHARGE mode, automatically. This switch,
in compliance with ABYC E-11, disconnects the neutral AC lead from the AC ground when
in shore/station power mode.
Features
1. Remote Panel LED Indicators
LED Color Function When Illuminated
Shore Station/ Power Charger Green Shore/station power Connected/Charging
Inverter Green Inverter On/Shore/station power disconnected
Fault Condition Red Fault Condition, See Troubleshooting Section
NOTE: This panel is removable from the TruePower Combi unit to be located in an area of
greater convenience. A dummy plate is included in the package. See the Installation
section for more details on removal of the remote panel and installation of the dummy plate.
2. Three Position Rocker Switch (Inverter feature ONLY)
Switch Position Action
Auto Standby Power on with Standby mode. Loads connected
below 20W will NOT activate the Inverter
Power Off Both the Inverter and the charger disabled.
Power On, Without Auto Standby Power to Inverter is enabled, Auto Standby disabled.
Resetting the Unit After a Fault Cycle power Off, then On again, the unit will reset.
The unit will continue to shut down if the fault is
present. In this event, consult the Troubleshooting
section of this manual.
DC Connections
Battery Type Selector
LED Status Indicator Center
AC Connections
1.Remote Panel Indicator LED’s
2.Auto Standby/Off/On Switch