TOHO ELECTRONICS TTM000 - Manual (Page 38)

38
Identifier Relative
address
Absolute
address
Character Name R/W Description
□MD 0028h 40041 Control mode setting R/W R/W the control mode setting
Control execution: 00000
Manual control: 00001
Control stop: 00002
Auto-tuning in progress: 00003
CNT 002Ah 40043 Selection of control type setting R/W R/W the control type setting
DIR 002Ch 40045 Change of normal or reverse R/W R/W the forward/reverse operation
switchover setting
MV1 002Eh 40047 Manipulated value
for output 1
R/W R/W the output 1 operation amount
TUN 0030h 40049 Set for PID tuning type R/W R/W the tuning type setting
ATG 0032h 40051 AT coefficient setting R/W R/W the AT factor
ATC 0034h 40053 AT sensitivity setting R/W R/W the AT sensitivity
□P1 0036h 40055 Proportional band setting
for output 1
R/W R/W the output 1 proportional band setting
□I1 0038h 40057 Integral time setting R/W R/W the integral time setting
□D1 003Ah 40059 Derivative time setting R/W R/W the derivative time setting
□T1 003Ch 40061 Proportional cycle setting
For output 1
R/W R/W the output 1 proportional frequency
setting
ARW 003Eh 40063 ARW(Anti-reset windup) setting R/W R/W the anti-reset windup
MH1 0040h 40065 High limit setting of manipulated
value for output 1
R/W R/W the amount-of-operation limiter upper
limit setting
ML1 0042h 40067 Low limit setting of manipulated
value for output 1
R/W R/W the amount-of-operation limiter lower
limit setting
□C1 0044h 40069 Control sensitivity setting
for output 1
R/W R/W the output 1 control sensitivity setting
CP1 0046h 40071 OFF position setting for output 1 R/W R/W the output 1 off-point position setting
MV2 0048h 40073 Manipulated value for output 2 R/W R/W the output 2 operation amount
□P2 004Ah 40075 Proportional band setting
for output 2
R/W R/W the output 2 proportional band setting
□T2 004Ch 40077 Proportional cycle setting for
output 2
R/W R/W the output 2 proportional frequency
setting
MH2 004Eh 40079 High limit setting of manipulated
value for output 2
R/W R/W the amount-of-operation limiter upper
limit setting
ML2 0050h 40081 Low limit setting of manipulated
value for output 2
R/W R/W the amount-of-operation limiter lower
limit setting
□C2 0052h 40083 Control sensitivity setting
for output 2
R/W R/W the output 2 control sensitivity setting
CP2 0054h 40085 OFF position setting
for output 2
R/W R/W the output 2 off-point position setting
PBB 0056h 40087 Manual reset setting R/W R/W the manual reset
□DB 0058h 40089 Dead band setting R/W R/W the dead band setting
RP1 005Ah 40091 SV Ramp variation setting R/W R/W the SV lamp time setting
RP2 005Ch 40093 SV2 Ramp variation setting R/W R/W the SV2 lamp time setting
E1F 005Eh 40095 Function setting for EV1 R/W R/W the PV event output 1 function setting
E1H 0060h 40097 High limit setting for EV1 R/W R/W the event output 1 upper limit setting
E1L 0062h 40099 Low limit setting for EV1 R/W R/W the event output 1 lower limit setting
E1C 0064h 40101 Control sensitivity setting
for EV1
R/W R/W the event output 1 sensitivity setting
E1T 0066h 40103 Delay time setting for EV1 R/W R/W the event output 1 delay timer setting