ASKO T761 - Manual (Page 19)

Page 19
ENGLISH
ENGLISH
PROGRAMMING INSTRUCTIONS
Below are the basic instructions for changing a preset program. The following paragraphs explain the menus and how to
navigate through them. You can make temporary (one-time) program changes, or you can make permanent changes.
1. Press the button for the preset program
you want to change (
P1–P4
). The
program you select will display in the
lower left corner of the LCD window.
2. Press MENU until the menu you want
to change displays (e.g., Programs,
Temperature, etc.).
3. Press to scroll through the
available options or to toggle between off and on.
4. Press ENTER to save you settings and return to the Main Program screen. The LCD will display your new settings.
5. If you want to use this setting temporarily (for this one load), START . When the program ends it will revert back to
the previous setting.
6. If you want to save this setting permanently, press ENTER again then press START . The program will retain the change.
See “Navigating the Menus” below for detailed instructions on creating customized programs.
The table below lists the options available with each dry program. These options can be temporary or permanent,
depending on your preference. Refer to the “Programming Instructions” setting below for detailed instructions on how
to navigate the program menu and make temporary and permanent changes to the programs.
Program Dry Temp Cooling Time (1) Anti-Crease Buzzer Delay Start
Extra dry Normal or Low Normal or Quick 1, 2, or 3 hours On or Off 1 to 24 hours
Dry Normal or Low Normal or Quick 1, 2, or 3 hours On or Off 1 to 24 hours
Normal Dry Normal or Low Normal or Quick 1, 2, or 3 hours On or Off 1 to 24 hours
Iron Dry Normal or Low Normal or Quick 1, 2, or 3 hours On or Off 1 to 24 hours
Air fluff (2) n/a n/a 1, 2, or 3 hours On or Off 1 to 24 hours
Timed dry (2) Normal or Low Normal or Quick 1, 2, or 3 hours On or Off 1 to 24 hours
(1) The Normal cool-down cycle is 15 minutes; the Quick cycle is 5 minutes.
(2) The Air fluff and Timed dry programs require you to select a program time. You can select from 5 to 90
minutes, in 5-minute increments.
OPTIONS AVAILABLE WITH EACH PROGRAM
Start Stop
P1 P2 P3 P4
NOTES:
NAVIGATING THE MENUS
The following paragraphs explain how to navigate
through the menus and change the preset programs.
If you don’t want to make changes in all of the menus,
continue to press
MENU until the one you do want to
change displays.
To restore a preset program to the factory default settings,
simply press the button for the preset program (
P1–P4 )
you want to restore and hold it down while you press
ENTER
. The program will revert to the factory default
settings.
If you change your mind in the process of changing a
program, press the Power button to switch the dryer off.
When you switch the power back on, the program will
be as originally set.
Remember, the first step to customizing a preset
program is to press the button for the program
you want to customize (P1–P4).
The Program Menu
The Program menu lets you set the dry program you
prefer. You would also use this menu to set the machine
for a Timed Dry or Air Fluff program. (See “Timed Dry
and Air Fluff” on this page.)
1. Press MENU until “Select Program” displays.
2. Press to scroll through the program choices
(Extra Dry, Dry, Normal, etc.)
3. When your preference displays, press ENTER . The
LCD will display the new program setting.
4. If you only want to use this setting temporarily (for
this one load), press START . When the program
ends it will revert back to the previous setting.
5. If you want to save this setting permanently, press
ENTER again then press START . The program will
retain the change.