Alpine VPA-B222R - Manual (Page 17)

16
-EN
01GB05VPAB222R.fm
ALPINE VPA-B222R 68-02065Z87-A (EN)
3
Press the joystick up or down to select the desired
item.
Setting items:
IN-INT MUTE / NAV. / GUIDE MIX / NAV. MIX LV / FACT SYS SET
/ FACT SYS LV / FACT SYS DET / FACT SYS MIX / F.SYS MIX TYP
/ F.SYS INT CH. / REMOTE SEL.*
1 / AUX IN-1(2,3) / AUX IN-
1(2,3) NAME / AUX IN-1(2,3) LEVEL / MONITOR-1 / MONITOR-2
/ VISUALIZER / ILLUM COLOR / CMNDR LIGHT. / DIMMER /
SCREEN ADJ / SUBW*
2
* 1 Refer to "Rear Entertainment Function" on page 12.
* 2 When an external audio processor is connected, the SUBW item is
not displayed.
4
Press the joystick left or right to adjust and set the
desired item.
5
Press TA/RTN/SETUP to return to the previous
screen. Press TA/RTN/SETUP repeatedly to return
to the main source screen displayed before starting
the setup operation.
• Select SETUP on the FUNCTION screen to recall the SETUP screen
after pressing and holding /MENU/FUNC. for at least 2 seconds.
• Immediately after changing the settings of System Mode (While the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF. Otherwise, the settings may not be changed.
Using the Speaker Input
The unit can interrupt the system (navigation or telephone) of the car.
The audio can also be played back on the unit if the car system of the
audio (CD, etc.) is selected as the source.
The unit makes the sound interruption according to the sound output
level of the car system. If any of the following settings are not correctly
made, sound may not interrupt, or loud sound may suddenly interrupt.
The following explains how to install the system (navigation/telephone)
in your car. While listening to the radio, you can have navigation voice
guidance or a received telephone call interrupt automatically. You can
also select the speaker input mode (FACTRY SYS) on the source
selection screen.
Setting items: FACT SYS SET
Setting content: OFF / SOURCE / INT / BOTH
• If the car system (CD, etc.) is set to SOURCE and played back in a
car with multi-channel speakers, sound such as treble, etc., may not
be correctly output.
• Depending on the conditions of use, the INT or SOURCE setting is
recommended.
• If INT is set, do not output CD audio from the car system.
• With BOTH set, if the source is set to other than FACTORY SYS, do
not output CD audio, etc., from the car system.
• If OFF is to set, speaker input mode settings cannot be made.
The volume level of the speaker input is displayed numerically.
Adjustment can be made only on the system in your car (standard car
audio, etc.), and cannot be made by this unit.
Setting items: FACT SYS LV
Setting content: 0 to 2 L / 3 to 15: OK / 16 to 18 H
Adjust the volume for optimum level.
• Set the volume as loud as possible, but before the onset of distortion
(The volume level should not exceed 15). Even if OK is displayed, if
any distortion is apparent, decrease the car audio's volume.
• Turn off the car audio's TREBLE, BASS settings.
• The volume level cannot be displayed when OFF is set in "Setting the
Speaker Input Mode" (page 16).
Setting the Speaker Input Mode
SOURCE: The system (CD, etc.) of the car can be selected as a
source.
Navigation/telephone voice of the car is not
interrupted.
INT: Interrupts only the navigation/telephone voice of the
car.
BOTH: The system (CD, etc.) of the car can be selected as
the source.
Navigation/telephone voice of the car is interrupted.
OFF: Operation and setting of the speaker input mode is
not performed.
Displaying the Speaker Input Volume Level
L: Volume level is LOW
OK: Volume level is optimally adjusted
H: Volume level is HIGH
01GB00VPAB222R.book Page 16 Monday, January 23, 2006 4:24 AM