Kenwood KDC-BT92SD - Manual (Page 21)

41 | KDC-BT92SD English | 42
Clock and Other Functions
Theft Deterrent Faceplate
The faceplate of the unit can be detached and
taken with you, helping to deter theft.
Removing the Faceplate
1 Press the Release button.
Drop open the faceplate.
2 Drawing the faceplate to left side pull it to
forward and remove it.
¤
• The faceplate is a precision piece of equipment and can
be damaged by shocks or jolts.
• Keep the faceplate in its faceplate case while detached.
• Do not expose the faceplate (and the faceplate case) to
direct sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
Reattaching the Faceplate
1 Align the shaft on the unit with the depression
on the faceplate.
2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to
use the unit.
Initial Settings
You can select following Initial Setting items.
1 Select the Standby
Pressing the [SRC] button repeatedly switches
source.
Select the “STANDBY” display.
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2 Enter Menu List mode
Press the [MENU] button.
3 Enter Initial Setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Initial Settings”.
4 Select the setting item to adjust
Turn the [VOL] knob.
Display Overview
“Initial Settings”
“SRC Select” Sets the source selection method.
“Settings 1”/ “2”
“Beep” Setting the operation check sound (beep sound)
ON/OFF.
“OFF”/ “ON”
“Russian” When this is set to ON, the following character
strings are displayed in Russian:
Folder name/ File name/ Song title/ Artist
name/ Album name
“OFF”/ “ON”
“Menu Language” You can select the display language for the
Menu list item.
“English”/ “Français”/ ”Español”/ “Deutsch”/
“Italiano”/ “Pyccкий”
“Power OFF Wait” Setting the timer to turn this unit’s power OFF
automatically when Standby mode continues.
Using this setting can save the vehicle’s battery
power.
“-----”/: Power OFF Timer function is OFF.
“20min”/ “40min”/ “60min”: Turns the power
OFF after minutes.
“Built in AUX” When this is set to ON, AUX source can be
selected.
“ON”: Allows AUX source to be selected. Use
this setting when the built-in AUX terminal
is connected to the external equipment all
the time.
“OFF”: Disable AUX source selection. Use this
setting when the built-in AUX terminal is
not used.
“Forced CD-DA” Sets the CD read mode.
“Settings 1”: Automatically distinguishes
between audio file disc and music CD when
playing disc.
“Settings 2”: Forces playing as music CD.
“Built in AMP” Selecting “OFF” turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
“OFF”/ “ON”
“DSI” DSI (Disabled System Indicator) of the unit blinks
when the faceplate is removed.
“OFF”/ “ON”
“F/W Update” Updates the firmware. The update information
will be posted on the following URL as
necessary.
www.kenwood.com/cs/ce/
( : Factory setting)
5 Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
6 Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Demonstration mode Setting
Turning the demonstration mode ON/OFF.
1 Enter Menu List mode
Press the [MENU] button.
2 Enter Demonstration mode setting
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “DEMO Mode”.
3 Set the Demonstration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “ON” or “OFF”.
4 Exit Menu List mode
Press the [MENU] button.