Kenwood KDC-BT92SD - Manual (Page 23)

45 | KDC-BT92SD English | 46
Audio Adjustments
Manual Equalizer Control
You can adjust following Equalizer Control items.
Band Item Range
“BAND1” (62.5 Hz) “GAIN” Band level -9 –+9 dB
“B.Ex” Bass Effect “ON”/ “OFF”
“BAND2” (100 Hz) “GAIN” Band level -9 –+9 dB
“BAND3” (160 Hz) “GAIN” Band level -9 –+9 dB
“BAND4” (250 Hz) “GAIN” Band level -9 –+9 dB
“BAND5” (400 Hz) “GAIN” Band level -9 –+9 dB
“BAND6” (630 Hz) “GAIN” Band level -9 –+9 dB
“BAND7” (1 kHz) “GAIN” Band level -9 –+9 dB
“BAND8” (1.6 kHz) “GAIN” Band level -9 –+9 dB
“BAND9” (2.5 kHz) “GAIN” Band level -9 –+9 dB
“BAND10” (4 kHz) “GAIN” Band level -9 –+9 dB
“BAND11” (6.3 kHz) “GAIN” Band level -9 –+9 dB
“BAND12” (10 kHz) “GAIN” Band level -9 –+9 dB
“BAND13” (16kHz) “GAIN” Band level -9 –+9 dB
“BAND1” – “BAND13” “Q” Quality 1.35/ 1.5/ 2.0
( : Factory setting)
1 Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2 Enter Audio Control mode
Press the [VOL] knob.
3 Enter Manual Equalizer Control mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Manual Equalizer”.
4 Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
5 Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
6 Exit Audio Control mode
Press the [MENU] button for at least 1 second.
⁄
• When “iPod” is selected in the section <Preset Equalizer
curve Select> (page 44) , Manual Equalizer Control is
disabled.
• You can select for each source.
Dual Zone System
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
Display Overview
“2 Zone” Sets the Dual Zone System.
“OFF”/ “ON”
“2 Zone Rear Volume”* Adjust the volume of Rear channel.
“0” — “35”
“2 Zone Select”* Specifies the destination of sub source sound
when the Dual Zone function is turned on.
“Rear”/ “Front”
* The Dual Zone System is set to “ON”.
( : Factory setting)
1 Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2 Enter Audio Control mode
Press the [VOL] knob.
3 Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Pro Setup”
> “Zone Control”.
4 Select the item you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
5 Exit Audio Control mode
Press the [MENU] button for at least 1 second.
⁄
• Select Main source by [SRC] button.
• Adjust the volume of Front channel by [VOL] knob.
• The Audio Control has no effect on sub source.
• There are following limitations when Dual Zone System
is enabled.
- There is no output from the subwoofer.
- “Fader”, “Subwoofer Level” of
<Audio Control> (page 43)
and DSP function are not available.
• The Bluetooth audio source can be set exclusively to the
front speaker. Set “2Zone Select” to “Rear”.