Asus TW510-E2 - Manual (Page 71)

4 - 7 4 - 7 4 - 7 4 - 7 4 - 7 A S U S T W 5 1 0 - E 2 A S U S T W 5 1 0 - E 2 A S U S T W 5 1 0 - E 2 A S U S T W 5 1 0 - E 2 A S U S T W 5 1 0 - E 2
2 . 2 . 2 . 2 . 2 . I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E 1 , S E C _ I D E 1 ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E 1 , S E C _ I D E 1 ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E 1 , S E C _ I D E 1 ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E 1 , S E C _ I D E 1 ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E 1 , S E C _ I D E 1 )
These connectors are for Ultra DMA 100/66 signal cables. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for
the primary IDE connector on the motherboard, a black connector for
an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive),
and a gray connector for an Ultra DMA 100/66 IDE master device (hard
disk drive). If you install two hard disk drives, you must configure the
second drive as a slave device by setting its jumper accordingly. Refer
to the hard disk documentation for the jumper settings.
4.3 Internal connectors
1 . 1 . 1 . 1 . 1 . F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 )
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
• The Pin 20 on the IDE connector is removed to match the covered
hole on the Ultra DMA cable connector. This prevents incorrect
insertion when you connect the IDE cable.
• Use the 80-conductor IDE cable for UltraDMA 100/66 IDE devices.
K8N-DL ®
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
PIN 1
FLOPPY1
K8N-DL Floppy disk drive connector
K8N-DL IDE connectors
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE1
PRI_IDE1
PIN 1
K8N-DL ®