ATTO Technology 2700C - Manual (Page 42)

ix
ATTO Technology Inc. iPBridge Installation and Operation Manual
IPGateway
Controls the current default gateways used by any
Ethernet ports on the iPBridge. If
IPDHCP is enabled,
the get command reports the current IP gateway
assigned by the network DHCP server.
Default: 0.0.0.0
set IPGateway [DPn | mp1 | all] [xxx.xxx.xxx.xxx]
SaveConfiguration Restart command required
get IPGateway [DPn | mp1 | all]
IPSubnetMask
Controls the current subnet masks used by any Ethernet
ports on the iPBridge. If
IPDHCP is enabled, the get
command reports the current IP subnet mask assigned by
the network DHCP server.
Default: 255.255.0.0
set IPSubnetMask [DPn | mp1 | all] [xxx.xxx.xxx.xxx]
SaveConfiguration Restart command required
get IPSubnetMask [DPn | mp1 | all]
iSCSIAlias
Assigns a human-readable name to the iPBridge. Aliases
may be 1 to 64 characters in length and may contain
spaces if enclosed in quotes.
set iSCSIAlias [Alias]
get iSCSIAlias
iSCSIChap
Regulates whether CHAP (Challenge-Handshake
Authentication Protocol) is to be used for the iSCSI
protocol. If CHAP is enabled, the target requires the
initiator to negotiate CHAP authentication using the
CHAP secrets. An initiator may reject this negotiation. If
discovery is specified, the setting applies to CHAP
during discovery sessions.
set iSCSICHAP [default | Target Name | discovery]
[enabled | disabled]
get iSCSICHAP [default | Target Name | discovery]
iSCSIChapSecret
Specifies the incoming and outgoing passwords for iSCSI
CHAP sessions. Secrets are case sensitive, 12 to 32
characters, and cannot contain spaces. In and out
secrets must be different for each name. If discovery is
specified, the setting applies to CHAP during discovery
sessions. An in secret authenticates the server to the
iPBridge. The iPBridge can store up to 32 in secrets,
each with a unique Account Name and secret pair. An out
secret authenticates the iPBridge to the server. There is
only one out secret per target which cannot be deleted.
The account name for the out secret is root by default.
set iSCSICHAPSecret [default | target name | discovery]
[in [Account Name | all] | out [root] | delete [Account
Name | all]] <Secret>
get iSCSICHAPSecret [default | target name | discovery]
[in [Account Name | all] | out [root]]
iSCSIInitiators
Displays a list of previous and current successfully
logged-in iSCSI initiators, including successful initiators
recorded in the event log and any initiators manually
added since the last reboot. This list is cleared if the event
log is cleared.
iSCSIInitiators
iSCSIPortNumber
Specifies the port number which listens for iSCSI
connections. Port number must be between 1024 and
65535 with the exception of port 860.
Default: 3260
set iSCSIPortNumber [DPn | all] [portnumber]
get iSCSIPortNumber [DPn | all]
iSCSITarget
Creates/deletes an iSCSI target. The target name acts as
a suffix to the standard iPBridge iSCSI-qualified name.
The target name may not exceed 24 characters. A newly-
created target has one LUN, the iPBridge LUN, at LUN
0.
AccessControl is enabled by default, unless
iSNSLoginControl is already enabled. If the target
name already exists, this command does nothing. The
default target cannot be deleted.
iSCSITarget [Target Name] <delete>
iSCSITargetNameDisplay
Displays the iSCSI target name.
iSCSITargetNameDisplay