AEM 30-3520 Infinity Plug & Play Harnesses - Nissan/Infiniti 2003-2006 350Z/G35 - Manual (Page 31)

2003–2006 Nissan 350Z/Infiniti G35 31
© 2014 AEM Performance Electronics
Infinity
Pin
Hardware Reference
2003–2006 350Z/
G35
Specification
Dest. Pin
350Z/
G35
Hardware Specification Notes
C1-54 Harness_HBridge0_1 HBridge0_1 5
5.0A max Throttle Control
Hbridge
+12V to Open
C1-55 Power Ground Ground 115 Power Ground Connect directly to battery ground.
C1-56 Harness_Injector_5 Injector 6 40
Saturated or peak and
hold, 3A max continuous
Injector 6
C1-57 Harness_Injector_4 Injector 5 21
Saturated or peak and
hold, 3A max continuous
Injector 5
C1-58 Harness_Injector_3 Injector 4 41
Saturated or peak and
hold, 3A max continuous
Injector 4
C1-59 Harness_Injector_2 Injector 3 22
Saturated or peak and
hold, 3A max continuous
Injector 3
C1-60 Power Ground Ground 115 Power Ground Connect directly to battery ground.
C1-61 +12V +12V In 119 12 v olt power f rom relay
12 v olt power f rom relay . Relay must
be controlled by +12V Relay Control
signal, pin C1-29 abov e.
C1-62 Harness_Injector_1 Injector 2 42
Saturated or peak and
hold, 3A max continuous
Injector 2
C1-63 Harness_Injector_0 Injector 1 23
Saturated or peak and
hold, 3A max continuous
Injector 1
C1-64 +12V +12V In 120 12 v olt power f rom relay
12 v olt power f rom relay . Relay must
be controlled by +12V Relay Control
signal pin C1-29 abov e.
C1-65 Harness_+12V_SW Ignition Switch 109 10K pulldown
Full time battery power must be
av ailable at C1-10 bef ore this input is
triggered.
C1-66 Harness_Analog_In_Temp_1
Coolant Temp
Sensor
73
12 bit A/D, 2.49K pullup
to 5V
See CoolantTempCal [C] table f or
calibration data and CoolantTemp [C]
f or channel data.
C1-67 Harness_Analog_In_Temp_2
Intake Air
Temperature
34
12 bit A/D, 2.49K pullup
to 5V
See AirTempCal [C] table f or
calibration data and AirTemp [C] f or
channel data.
C1-68 Harness_Analog_In_Temp_3
Oil Temperature
Sensor
12 bit A/D, 2.49K pullup
to 5V
See OilTempCal table f or calibration
data and OilTemp [C] f or channel
data.
C1-69 Harness_Stepper_2A Stepper 2A
Programmable Stepper
Driv er, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor is properly paired with
the 1A/1B and 2A/2B ECU outputs.
Supports Bi-Polar stepper motors only .
C1-70 Harness_Stepper_1A Stepper 1A
Programmable Stepper
Driv er, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor is properly paired with
the 1A/1B and 2A/2B ECU outputs.
Supports Bi-Polar stepper motors only .
C1-71 Harness_Stepper_2B Stepper 2B
Programmable Stepper
Driv er, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor is properly paired with
the 1A/1B and 2A/2B ECU outputs.
Supports Bi-Polar stepper motors only .