AEM 30-3520 Infinity Plug & Play Harnesses - Nissan/Infiniti 2003-2006 350Z/G35 User Manual
Page 34
34
© 2014 AEM Performance Electronics
P/N 30-3520
Infinity
Pin
Hardware Reference
2003–2006 350Z/
G35
Specification
Dest. Pin
350Z/
G35
Hardware Specification
Notes
C2-28
Harness_VR+_In_4
Non Driv en
Right Wheel
Speed Sensor +
C2-29
Harness_LowsideSwitch_9
Tachometer
Lowside switch, 4A max
with internal f ly back
diode, 2.2K 12V pullup.
Inductiv e load should
NOT hav e f ull time
power.
Nissan tachometer is driv en v ia CAN
bus.
C2-30
AGND_2
Sensor Ground
O2
78
Dedicated analog ground
Analog 0–5V sensor ground
C2-31
AGND_2
Sensor Ground
APP1
82
Dedicated analog ground
Analog 0–5V sensor ground
C2-32
AGND_2
Sensor Ground
APP2
83
Dedicated analog ground
Analog 0–5V sensor ground
C2-33
Harness_Analog_In_20
MAF
51
12 bit A/D, 100K pullup to
5V
Nissan MAF sensor not currently
supported
C2-34
Harness_Analog_In_21
3 Step Enable /
TPS 2B
12 bit A/D, 100K pullup to
5V
0–5V analog signal. Use +5V Out pins
as power supply and Sensor Ground
pins as the low ref erence. Do not
connect signals ref erenced to +12V as
this can permanently damage the
ECU. See 3StepSwitch 1-axis table f or
setup.
C2-35
Harness_Analog_In_22
Ref rigerant
Pressure Sensor
70
12 bit A/D, 100K pullup to
5V
See "AC_Pressure [kPa]" f or AC
pressure conf iguration. Required f or
proper AC f unction.
C2-36
Harness_Analog_In_23
Charge Out
Pressure
12 bit A/D, 100K pullup to
5V
0–5V analog signal. Use +5V Out pins
as power supply and Sensor Ground
pins as the low ref erence. Do not
connect signals ref erenced to +12V as
this can permanently damage the
ECU. See ChargeOutPress [kPa]
channel f or input state. See Setup
Wizard page Charge Out Pressure f or
calibration options.
C2-37
Harness_Digital_In_6
Stop Lamp
Switch
101
No pullup. Will work with
TTL signals.
See AC_Request_In 1-axis table f or
setup options. Input can be assigned
to dif f erent pins. See Setup Wizard
page Input Functions f or input
mapping options.
C2-38
Harness_Digital_In_7
Brake Switch
108
No pullup. Will work with
TTL signals.
See ClutchSwitch 1-axis table f or
setup options. Input can be assigned
to dif f erent pins. See Setup Wizard
page Input Functions f or input
mapping options.
C2-39
Power Ground
Ground
1
Power Ground
Connect directly to battery ground.
C2-40
Power Ground
Ground
1
Power Ground
Connect directly to battery ground.
C2-41
Harness_CanH_Bout
CANH
94
Dedicated High Speed
CAN Transceiv er
Used f or Nissan CAN bus
C2-42
Harness_CanL_Bout
CANL
86
Dedicated High Speed
CAN Transceiv er
Used f or Nissan CAN bus