AEM 30-3520 Infinity Plug & Play Harnesses - Nissan/Infiniti 2003-2006 350Z/G35 - Manual (Page 35)

2003–2006 Nissan 350Z/Infiniti G35 35
© 2014 AEM Performance Electronics
Infinity
Pin
Hardware Reference
2003–2006 350Z/
G35
Specification
Dest. Pin
350Z/
G35
Hardware Specification Notes
C2-43 Harness_LowsideSwitch_8 VVC2B 8
Lowside switch, 6A max
with internal f ly back
diode. Inductiv e load
should NOT hav e f ull
time power.
See Setup Wizard Page LowSide
Assignment Tables f or activ ation
criteria.
C2-44 Harness_LowsideSwitch_7 EVAP Purge 45
Lowside switch, 1.7A
max with internal f ly back
diode. Inductiv e load
should NOT hav e f ull
time power.
See Setup Wizard Page LowSide
Assignment Tables f or activ ation
criteria.
C2-45 Harness_UEGO_VM_2 UEGO 2 VM 57
Bosch UEGO Controller
Virtual Ground signal. Connect to pin 5
of Bosch UEGO sensor.
C2-46 Harness_UEGO_UN_2 UEGO 2 UN 76
Nernst Voltage signal. Connect to pin
1 of Bosch UEGO sensor.
C2-47 Harness_UEGO_IP_2 UEGO 2 IP 58
Pumping Current signal. Connect to
pin 6 of Bosch UEGO sensor.
C2-48 Harness_UEGO_IA_2 UEGO 2 IA 77
Trim Current signal. Connect to pin 2
of Bosch UEGO sensor.
C2-49 Harness_UEGO_Heat-_2 UEGO 2 HEAT 24
Lowside switch f or UEGO heater
control. Connect to pin 4 of Bosch
UEGO sensor. NOTE that pin 3 of the
Sensor is heater (+) and must be
power by a f used/switched 12V
supply .
C2-50 +12V_R8C_CPU
Battery Perm
Power
Dedicated power
management CPU
Optional f ull time battery power. MUST
be powered bef ore the ignition switch
input is triggered (See C1-65).
C2-51 Harness_Coil_6 Coil 7
25 mA max source
current
0–5V Falling edge f ire. DO NOT
connect directly to coil primary . Must
use an ignitor OR CDI that accepts a
FALLING edge f ire signal.
C2-52 Harness_Coil_7 Coil 8
25 mA max source
current
0–5V Falling edge f ire. DO NOT
connect directly to coil primary . Must
use an ignitor OR CDI that accepts a
FALLING edge f ire signal.
C2-53 Harness_Coil_8 Coil 9
25 mA max source
current
0–5V Falling edge f ire. DO NOT
connect directly to coil primary . Must
use an ignitor OR CDI that accepts a
FALLING edge f ire signal.
C2-54 Harness_Coil_9 Coil 10
25 mA max source
current
0–5V Falling edge f ire. DO NOT
connect directly to coil primary . Must
use an ignitor OR CDI that accepts a
FALLING edge f ire signal.
C2-55
Harness_HighsideSwitch_2/
Harness_Coil_10
Fuel Pump 1
Multi-f unction pin
depending on hardware
conf iguration +12V High Side Driv e. Will prime f or 2
seconds at key on and activ ate if
RPM > 0.
C2-56
Harness_HighsideSwitch_3/
Harness_Coil_11
Not used
Multi-f unction pin
depending on hardware
conf iguration
Not used