Behringer Eurolight 24-Channel DMX Lighting Console LC2412 - Manual (Page 16)

16 EUROLIGHT LC2412 User Manual
6.3.2 Previewing and editing CTM
Replay mode and speed
After successfully programming a chase, you can also preview the replay mode
and the chase speed, without any of these being visible on the stage. This is
particularly uselful when you are arranging a light show and don’t have time to
program a chase in peace.
1. Use the PREVIEW key (21) and select a memory (flash keys 9 - 12) you wish to
preview and/or edit.
Fig 6.7: Display “previewing and modifying CTM”
Memory (11) and bank (04) are shown at the top right-hand side of the display.
2. Enter beat measure and replay mode, as described in chapter 6.3 under
point 5.
3. Exit the programming sequency by pressing QUIT.
6.4 Previewing chases in live mode
You can use the live mode for chases as well. More detailed information about
live mode can be found in chapter 4.5.
To preview chases in live mode, do the following:
1. Activate the live mode by pressing the LIVE switch (30).
2. Press the NUMBER key (48). The chase is previewed on the stage as long as
you keep the key pressed.
3. To quit live mode, simply press the LIVE switch again.
7. Additional Functions
of the LC2412
7.1 Locking program mode
To avoid having your setups altered by unauthorized persons, you can block the
program mode of your console. There are several blocking functions available.
LOCK PRESET mode
The LC2412 can run only in preset mode. Recalling memories is not possible.
Chases can still be replayed.
LOCK PROGRAMMING mode
The console operates normally, but modifying programmed memories or chase
steps is possible only after the console is unblocked.
Blocking/unblocking
1. Keep the SOFT A and SOFT B keys pressed and simultanously press the FLASH
key for channel 1 (far left).
2. Now you can select various menues with the DATA wheel.
3. After having selected the desired mode, you can block it/unblock it by
pressing the SOFT B key.
4. Exit the programming procedure by pressing QUIT.
7.2 Putting the output on hold
If you want to freeze the current console output while you can make another
setup, you can use the HOLD key for this purpose.
1. Press the HOLD key (46).
Fig 7.1: Display “put console output on hold”
2. Implement a modification, as desired (recalling and programming memories
and presets is done as described in the respective chapters of this manual).
3. To start a new chase, select this chase as usual by pressing the NUMBER key
and turning the DATA wheel. The chase selected will be indicated on the
control lights as long as you keep the key pressed.
Releasing “Hold”
To softly crossfade between setups, pull the MAIN fader all the way down and
then all the way up. Moving up the fader crossfades between the former setup
and the new one.
The hold mode is automatically deactivated when the MAIN fader reaches its
upper-most position.
By using the SOFT B key, you can select “CANCEL” in the display, so that you quit a
mode. In doing so, the new setup is faded in abruptly.
7.3 Special channels
Both special channels (8) and (9) are well-suited activating effects
independently from other settings of the EUROLIGHT LC2412. Fog machines,
color changers or disco ball motors are such effects. You can program special
activation modes for these effects.
• Toggle mode: The SPECIAL key acts as a switch. Pressing and releasing
the key activates the fog machine (or another function). To deactivate it,
press and release the SPECIAL key again.
• Flash mode: The SPECIAL key keeps a function active as long as you keep
the key pressed. As soon as you let go of the SPECIAL key, the function
assigned to this channel is again deactivated.
• Kill mode: Similar to flash mode, a function is activated only as long as the
SPECIAL key is kept pressed. However, in addition to this, all other functions
are also temporariliy disabled.
To program the various modes, do the following:
1. Press the UTILITY 2 key (29).
2. Select the “MORE” option using SOFT B.
3. Select the “SELECT SPECIAL” option on the display by using the
SOFT A key (38).
4. SPECIAL 1 key is now labeled with KEY 1 (SPECIAL 2: KEY 2). To change
the mode of this key, keep the SOFT A key (for KEY 1; SOFT B for KEY 2)
pressed and select the desired option using the DATA wheel.
5. Confirm your selecting with the QUIT key (40) and go back to the main menu.
Special channels are labeled console channels 25 and 26 when assigned to DMX
channels (also see chapter 8.2.2.)