Online manual not for resale purposes – BLITZ DCII Meters User Manual

Page 6

Advertising

Gauge Functions
Press the MODE button to switch between readings. If the Green L.E.D. flashes once the gauge will
read in real time . If the Green L.E.D. flashes twice the gauge will read in delay mode.
If the Green L.E.D. flashes three times, the gauge will read in pass and hold mode.(Boost and Pressure readings only)
Power and RPM can read in realtime or passing/hold mode only. Temp,Speed and EGT can read in real time only.
Everytime the "MODE" switch is pushed it cycles from realtime to delay to passing hold. If MODE switch is held down it
goes into warning setting mode.

On the TEMP gauge the Mode switch toggles from Temp 1 to Temp 2
(For TEMP 1 the green LED is off and in TEMP 2 the green L.E.D. is on)
For the Speed/Power gauge each push of the MODE switch toggles from real time speed to real time power to
pass and hold power.
(In Speed mode the green L.E.D. is out and in Power mode the green L.E.D is on)
On the EX Temp/REV meter the Mode switch toggles from real time EGT to real time RPM to pass and hold RPM
(In EGT mode the LED is off and in REV mode the green L.E.D. is on)

Peak
Push the PEAK button once to show the highest reading achieved. The Yellow L.E.D. will
appear. Press the PEAK button again to get out of peak mode. To reset the peak, hold the
PEAK button down for 2 seconds when in peak display. The gauge will retain memory of
the last highest peak setting until it is reset on the gauge. When 2 sensors are used on the
TEMP sensor it can only show the peak value of the highest one(either 1 or 2) not both.

Warning
When the preset warning value is achieved the red led on the gauge will illuminate. If
optional LED warning indicator is installed it will also light. To set warning press MODE
button for 2 seconds. The Red L.E.D. will turn on. Press the PEAK button to move
increase warning and press the REC. button to decrease warning. Press the MODE
button to set. The Red L.E.D. should turn off.
For PRESSURE METER there is a low and high pressure warning. First set low
warning level and then press MODE button to set the high warning level. Press MODE
button again to set. If set improperly the Red L.E.D. will stay on. If optional external
warning LED is installed it will also illuminate.** The LOW pressure warning MUST
be set before HIGH pressure warning. On the TEMP gauge the warning value
applies to both sensors at the same time it cannot distinguish between temp 1 or
temp 2. (It is not possible to set each warning seperately)

Record
Press and hold Record button for 2 seconds in order to for the gauges to record. The
red L.E.D. will flash continuously while recording. Press the Record button again to
stop recording. All L.E.D. should be off when not recording. The Record feature can
record up to 99 seconds. After aproximately 89 seconds the red L.E.D blinks quickly
to inform it is nearing the end. You may also turn off the recording by pushing the
REC switch. Until new information is recorded over, it will hold memory of the last
recorded information. If the power source is interupted (ignition is turned off) while
recording the data recored will be deleted.

Peak display

YellowＬＥＤ

ＰＥＡＫ sw.

Set Warning

ＲＥＣ sw.
(ＤＯＷＮ）

RedＬEＤ

ＭＯＤＥ sw. ( 1 sec)

ＰＥＡＫ sw.（ＵＰ）

Record function

ＲＥＣ sw.
（１sec）

LED blinking

WARNING: All images and text in this manual is the property of Blitz Co., Ltd. (Japan). No part of this may be reproduced,

stored in retrevial systems, or transmitted in any form or means with out prior written permission of Blitz Co., Ltd. (Japan).

Online Manual Not For Resale Purposes

Advertising

Popular Brands

Popular manuals