Barco R9001390 - Manual (Page 15)

5-1
Connections
5975938 BARCOREALITY 9200TCR+ 020798
5
R G B V R G B H / C V
On 98 2791
0 R G B H / C V H
9,'(2,1387
9,'(2 69,'(2
RS 232 IN REMOTE
PROJECTOR MODE :
GREEN - OPERATION
RED - STANDBY COMMUNICATION PORT
(800-PERIPHERALS) R S232 OUT
IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS CODE IR-RECEIVER
0 I T h i s d e vic e co m p lie s w it h P a r t 1 5 o f th e F C C r u le s . O p e ra t io n is s u b je c t to fo ll o w in g t w o c o n d itio n s : ( 1 ) T h is d e vi ce m a y n o t c a u se h a r m f u l in te r fe r e n c e ( 2 ) T h is d e vi ce m u s t a cc e p t a n y in t e rf e r e n c e r e ce i ve d in c lu d in g in t e r fe r e n c e t ha t m a y c a u se u n d e si re d o p e r at io n
COLOR PHASE
SHARPN TINT BRIGHTN
STANDBY
ENTER
TEXT
EXIT
PAUSE
 
 
 



&2175$67
ADJ E X IT
STBY T E X T
BRIGHTNESS
- +
- +
- +
- +
SHARPNESS
- +
T IN T
COLOR
CONTRAST
)5((=
0 9
7 8
6 5
4 3
2 1
(17(5
3$86(
- +
3+$6(
+(/3
R G B V R G B H / C V H
9,'(2,1387
9,'(2 69,'(2
RS 232 IN REMOTE
PROJECTOR MODE :
GREEN - OPERATION
RED - STANDBY COMMUNICATION PORT
(800-PERIPHERALS) R S2 32 OUT IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
CODE IR-RECEIVER
ГГ!"ГW
ГГ(ГГГГГ#Г6
Г%ГГГГ$ГC“
0 I T h is d e v ic e c o m p li es w i th P a r t 1 5 o f t h e F C C ru l e s. O p e r a tio n i s s ub je ct t o f o llo w in g t w o c o n d it io n s : ( 1 ) T h is d e v ic e m a y n o t ca u s e h a r m f u l in te r f er e n c e ( 2 ) T h is d e v ic e m u st a c ce p t a n y i n te r fe r e n c e r e c e ive d i n cl ud in g in te r fe re n c e t h a t m a y c a u s e u n d e s ir e d o p e r a tio n
RS 232 IN
COMMUNICATION PORT
(800-PERIPHERALS) RS232 OUT
0 I
Projector mode indication
Stand by button
Switching on
Use the power switch to switch on.
When '0' is visible, the projector is switched off.
When '1' is visible, the projector is switched on.
When switching on with the power switch, the projector starts in the
stand by mode. The projector mode indication lamp is red.
To start image projection :
a. press the 'Stand by' button on the local keypad or on the remote
control. The projector mode indication lamp will be green.
b. press a digit button to select an input source. The projector mode
indication lamp will be green.
CONNECTIONS
AC Power (mains) cord connection
Use the supplied power cord to connect your projector to the wall
outlet. Plug the female power connector into the male connector at
the front of the projector.
The power input is auto-ranging from 200 to 240 VAC.
This projector may be connected to an IT-power system.
Fuses
Warning
For continued protection against fire hazard :
- refer replacement to qualified service personnel
- ask to replace with the same type of fuse.
Fuse type : T16 AH/250V
230V
10A
50/60 Hz